Mira 1.1532.353 Скачать руководство пользователя страница 6

6

Caution!

1.  Read all of these instructions and retain this guide for later use

.

2.

  Make sure that this guide is left with the user

Pass on this guide in the event 

of change of ownership of the installation site.

3. 

Follow all warnings, cautions and instructions contained in this guide, and on 

or inside the shower.

4.

  Installation must be carried out in accordance with these instructions, and must 

be conducted by designated, qualified and competent personnel.

5. 

The electrical installation must comply to ‘BS 7691

 

Requirements for Electrical 

Installations’ (commonly referred to as the IEE Wiring Regulations Part 7, or 

any particular regulations and practices, specified by the local electricity supply 

company) in force at the time of installation. The installation should be carried 

out by an electrician or contractor who is registered, or is a member of, an 

association such as:

• 

National Inspection Council for Electrical Installation and Contracting 

(NICEIC), throughout the UK

• 

The Electrical Contractors Association (ECA), England and Wales

• 

The Electrical Contractors Association of Scotland (ECAS)

6. 

This is a high power unit; it is essential to contact your electricity supply company 

to make sure that the electricity supply is adequate for the purpose.

7. 

The  plumbing  installation  must  comply  with  the  requirements  of  UK  Water 

Regulations/Bye-laws  (Scotland),  Building  Regulations  or  any  particular 

regulations  and  practices,  specified  by  the  local  water  company  or  water 

undertakers. The installation should be carried out by a plumber or contractor 

who is registered, or is a member of, an association such as:

• 

Institute of Plumbing (IOP), throughout the UK

• 

National Association of Plumbing, Heating and Mechanical Services 

Contractors (NAPH & MSC), England and Wales

• 

Scottish and Northern Ireland Plumbing Employers’ Federation (SNIPEF), 

Scotland and Northern Ireland

8. 

This appliance is not thermostatic and can produce scalding temperatures if not 

operated in accordance with the instructions given in this manual.

9.

  If you are unsure how electric showers work, please read the 

Operation 

section 

before continuing.

10. 

This  appliance  is  not  intended  for  use  by  persons  (including  children)  with  

reduced physical, sensory or mental capabilities, or lack of experience and  

knowledge, unless they have been given supervision or instruction concerning 

the use of the appliance by a person responsible for their safety.

11.

  Children  should  be  supervised  to  make  sure  that  they  do  not  play  with  the 

appliance.

12. 

Sunburn or skin conditions can increase your sensitivity to hot water.

Содержание 1.1532.353

































Отзывы: