Mira 1.1532.353 Скачать руководство пользователя страница 5

5

21.

 

DO NOT

 commission this appliance if water leaks from the unit.

22.

 

DO NOT

 operate this appliance if water leaks from this appliance.

23. 

Only a competent person should remove the front cover. We recommend 

any maintenance work is carried out by a Mira Service Engineer or qualified 

tradesperson.

24. 

Mains connections are exposed when the cover is removed. Isolate the electrical 

and water supply before removing the cover.

25. 

If any of the following conditions occur, isolate the electricity and water supplies 

and refer to 

To contact us

, on the back page of this guide.

• 

If the cover is not correctly fitted and water has entered the appliance case

• 

If the case is damaged

• 

If the shower begins to make an odd noise, smell or smoke

• 

If the shower shows signs of a distinct change in performance, indicating a 

need for maintenance

• 

If the the shower is frozen

26. 

The shower head must be de-scaled regularly. Lack of regular shower head 

cleaning will lead to poor performance and cause early failure of the appliance. 

Refer to the Shower Fittings User Guide for more information.

27. 

Unless otherwise stated, electrical equipment such as extractor fans, pumps 

must not be connected via this product.

28. 

If pipework and/or electical cables enter the shower from the rear through a hole 

in the wall . Provision must be made to prevent water ingress back into the wall 

structure. 

29. 

Care  is  required  when  adjusting  flow  or  temperature,  make  sure  that  the 

temperature has stabilised.

30.

  Rapid/Excessive movement of the flow and/or temperature control levers may 

result in momentary unstable blend temperatures.

31.  DO NOT

 position the handset to spray water directly on to the appliance. 

Eg.When cleaning shower control.

32.

  Make sure that you fully understand how to operate this shower and make sure 

that it is properly maintained in accordance with the instructions given in this 

manual.

33. 

Having completed the installation, make sure that the user is familiar with the 

operation of the appliance.

34. 

When this appliance has reached the end of its serviceable life, it should be 

disposed of in a safe manner, in accordance with current local authority recycling, 

or waste disposal policy.

Содержание 1.1532.353

































Отзывы: