background image

 

AFTER USE  

To raise the pad driver, push down until the pedal arm engages into the pedal catch. Turn 
machine off by turning the key switch on the control panel. Machine can be cleaned with a 
mild detergent and a damp cloth. Batteries should be charged after each use or when the 
battery condition meter shows a low charge. Once the battery charger reads 0 amps, the 
batteries are recharged. This should take approximately 8 hours if the batteries are 
completely discharged.  
 

MAINTENANCE  

Periodically remove batteries from machine. Clean the batteries and battery tray with a 
solution of baking soda and water. Check all battery cables and wiring for signs of damage 
and wear. Replace as needed. Grease front wheel and rear caster zerks once a month for 
best operation.  
 

FLOOR SEAL STRIP  

When the floor seal strip show signs of excessive wear, seal should be replaced. The strip 
can be removed by loosening the screw on the retainer strap until the seal can slide off of 
the pad shroud housing. To install new seal, slip the retainer strap over the new seal strip 
and pad shroud. Make sure the seal is seated equally around the perimeter and the holes 
on the floor seal are oriented towards the back portion of the shroud.  
 

BATTERY SERVICE AND INSTALLATION  

WARNING:

 Battery acid can cause burns. When working on or around batteries, wear 

protective clothing and safety glasses. Remove metal jewelry. Do not lay tools or metal 
objects on top of batteries.  
 

CHARGING OF BATTERIES  

Charging batteries generates explosive gasses. DO NOT CHARGE BATTERIES WHEN 
OPEN FLAMES OR SPARKS ARE PRESENT. DO NOT SMOKE. Make sure the charger 
is turned off before disconnecting it from the batteries. Charge the batteries in a well-
ventilated area with battery cover removed completely. Fluid levels should be checked 
before and after charging and maintained at the proper levels. If the burnisher is not used 
for extended periods of time, batteries should be kept fully charged with a boost charge 
once a week.  
 
 

 

6

Содержание Lumina 20 M26036TD



























Отзывы: