background image

MKA-42 OR MKA-52/62  

QUICK RELEASE BRACKET

1862014 & 1862016

Item / 

Assembly

Part #

Description

Qty.

Includes 2-6

2994829

BAG ASSY-MAX QUICK RELEASE

1

2

2073408

SCREW-1/4-20 X 7/8 PPH S/S

6

4

2261713

WASHER-1/4 FLAT 18-8 SS

6

6

2263103

NUT-1/4-20 NYLOCK SS

12

8

2500000

SCREW-1/4-20 X 2 1/4 PPH S/S

12

B

Includes 10-16

QUICK RELEASE MNT STD ASSY *MKA-42* *SHORT*

1

C

Includes 10-16

QUICK RELEASE MNT LG ASSY *MKA-52/62* *LONG*

1

10

SLIDE PLATE

1

12

BASE PLATE

1

14

2370101

THUMB SCREW

1

16

2371718

LOCKWASHER-1/4” ZINC

1

p

2374911

INSTR SHEET-MAX QUICK RLS.

1

The MKA-42 and MKA-52/62 are recommended for use with all Minn Kota

®

 Fortrex

®

, Maxxum

®

, Edge, and Ultrex freshwater trolling motors.

p

 Not shown on Parts Diagram. 

 This part is included in an assembly and cannot be ordered individually. 

TOOLS AND RESOURCES REQUIRED

•  Drill

•  9/32” Drill Bit

•  #3 Phillips Screw Driver

•  Awl, pencil or similar marking tool 

•  A second person to help with  

the installation

MOUNTING CONSIDERATIONS

It is recommended that the motor be mounted as close to 

the centerline of the boat as possible. The motor must not 

encounter any obstructions as it is lowered into the water or 

raised into the boat when stowed and deployed. Make sure the 

motor rest is positioned far enough beyond the edge of the 

boat. Make sure the area under the mounting location is flat, 

clear to drill holes and install nuts and washers.

12

12

10

10

2

2

A

A

B

B

C

C

4

4

6

6

8

8

WARNING

For motors with Lift Assist (Fortrex and Ultrex), the lift 

cylinder should be disengaged until installation is complete 

to prevent injury.

NOTICE:

 For Ultrex motors, please review the “Disconnect 

the Gas Spring” section of the Ultrex Owner’s Manual 

(#2297160) online a

minnkotamotors.com

.

NOTICE:

 For Fortrex motors, please review the 

“Disconnect the Gas Spring Pin” section of the Fortrex 

Owner’s Manual (#2287100) online at 

minnkotamotors.com

.

Complete Typical Installation

14

14

16

16

1  |  minnkotamotors.com

©2020 Johnson Outdoors Marine Electronics, Inc.

Содержание 1862014











Отзывы: