32
Chapter 6. Machine adjustment and setting up
GB
PROGRAM: P02
Type: Cold
cuts
Package nr.: 100
Expiry date:
21/01/2011
Gas type:
FOOD00
VE
SA CP AS SI IC LT
X
Press the button
(
▼
)
to switch to “Advanced functions”.
VE: Outside vacuum
SA: Soft Air
CP: Condition Program
AS:
Auto Seal Program
SI:
Sealing
IC: Infusion
cycle
LT: Liquid
time
Now press the buttons
(
▼
)
and
(
▲
)
to select the function.
Press the button
(
►
)
to activate the function (X appears) and
(
◄
)
to deactivate it.
VE “Outside vacuum”
This function allows obtaining the vacuum in special containers with a pipe directly to the packaging tank. The function
does not include the pack sealing phase.
PROGRAM:
P02
Time:
0.2 sec
Vacuum limit:
100.0%
Vacuum: 000.0%
Residual:
100.0%
Extra-vacuum: 00 sec
Gas ratio:
000.0%
START
If activated press the button (S), followed by the
(
▼
)
button in order to select
START
and start the cycle by pressing the button (S).
SA “Soft Air”
This function allows regulating the speed of air return into the tank, preventing uncontrolled movements of the packs (1
= minimum speed; 4 = top speed).
If enabled press the button (S) and select required speed. Press the Stop button (5) to confirm.
Note: If the function is active, but the lid fails to open at the end of the cycle, switch the machine off then on again, or
wait 50 seconds until the lid reopens. Check that the Soft Air valve has been installed correctly.
CP “Condition Program”
After a period of inactivity of the machine (at least 15 days) or after packaging products containing liquid products, it
may be necessary to eliminate liquid emulsion from the hydraulic fluid of the pump.
The problem that could arise concerns too much remaining air, or an interruption of the vacuum cycle due to having
exceeded the suctioning time.
If enabled press the button (S) to start an operating cycle lasting 4 minutes.
AS “Auto Seal Program”
The function envisages a packaging cycle with a fixed time irrespective of the vacuum level that has been reached,
defined beforehand. The basic time of the complete cycle is 25 seconds. The default increment is 4 seconds, however
it is possible to set up an increment time of between 0 to 8 seconds (corresponding to a base time of 25 + an increment
of 8 = 33 seconds).
This function is suitable for packaging products with excessive humid part.
By selecting this function, the operation of the machine remains basic. The only parameter that can be changed is the
ON time.
SI “Sealing”
The function envisages a packaging cycle with 60% max vacuum percentage. By selecting this function, machine
operation remains basic. The only parameter that can be changed is the sealing time.
IC “Infusion cycle”
This function can be used to carry out packaging procedures with delay that can be varied from 0.5 to 10 minutes
between the vacuum and sealing phases (ideal for marinated food products). After the delay, the cycle restarts,
restoring the set vacuum level if necessary.
Press the (S) button and set up the delay time using the
(
►
)
and
(
◄
)
buttons. Press the (S) button to confirm and
return to the previous page.
LT “Liquid time”
This function can be used to package pouches automatically with liquid products.
Press the (S) button and set up the function using the
(
►
)
and
(
◄
)
buttons, selecting the desired level from 1 to 10
(1 for cold products; 10 for hot products). Press the (S) button to confirm and return to the previous page.
The packaging cycle may also be interrupted by pressing the Stop (5) button.
Содержание MV35 XP PolyScience
Страница 83: ...82 7 8 ...
Страница 84: ...83 7 8 ...
Страница 85: ...84 7 9 ...
Страница 86: ......
