9
5. Sound activation mode on
6. Sound activation mode off
7. Microphone
8. Interchangeable projection discs
(Figure 3)
9. LED light
10. Speaker
11. Jack 3.5 mm audio input
12. Micro-USB DC connector
13. Jack-jack 3.5 mm audio cable
5. INSTRUCTIONS FOR USE
5.1. DEVICE POWER SUPPLY
dreamcube can be plugged in, so parents don’t have
to worry about battery life; or batteries can be used if
parents want to avoid using cords.
Follow these steps according to the power supply
that is chosen:
1. With the micro-USB cable that is included:
a. Connect the USB cable to the adapter and
the micro-USB end to the ‘DC 5V’ input on the
device.
b. Plug in the adapter.
2. With batteries:
a. Open the battery compartment lid on the
bottom of the projector.
b. Insert batteries observing the polarity symbols
shown in the compartment.
c. Ensure the lid is properly closed.
5.2. FUNCTIONS
This projector with sounds and melodies will help
your baby to relax and fall asleep. Thanks to its
sound activation system, dreamcube will start
automatically if it detects that your baby is crying,
and its relaxing lights and sounds will soothe your
baby.
The projector’s functions and how to use them are
explained below.
5.2.1. PROJECTOR FUNCTION
To start the projection, press the projection on button
in the shape of a light bulb (1). The light will change
colour (green, red and blue), and will soothe and
help the baby to fall asleep.
The device includes three different and
interchangeable projection discs: a starry sky, under
the sea and space. Please note that the disc that is
placed at the top of the projector will be the one that
is projected onto the wall. To change the disc, just lift
the tab you find round each one of the discs, as you
can see in
Figure 2
.
To switch the projection off, press the light bulb
button (1) again.
Note 1: Remove the protective plastic from the
projection discs before use Figure 3.
Note 2: Place the projection discs with the bright
side facing outwards.
5.2.2. MUSIC BOX FUNCTION
5.2.2.1. PLAYING PRELOADED SOUNDS
dreamcube includes 10 preloaded melodies and 5
sounds that have been specially selected to soothe
and relax babies. To activate them, press the button
in the shape of a musical note (2) or on the loop
button (4).
To change the song or sound, press the selection
button (4) until you get the one you want. dreamcube
repeats the same song by default. If you want to play
all the melodies and repeat them, hold the selection
button (4) pressed for three seconds until the next
song begins to play. The projector will then play all
the songs one after another.
To go back to repeating the same song, press the
selection button (4) again.
The speaker volume can also be adjusted by
pressing the volume control button (3). There are 5
levels and you can adjust the volume by pressing
this button.
The sound turns off automatically after about 30
minutes. To turn it off before then, press the musical
note button again.
Note 1:
If you turn the sound off, the device will
remember the last tune that was played and when
you turn it on again it will play that same tune.
Note 2:
Only melodies, not sounds, will be played
back cyclically.
5.2.2.2. PLAYING OTHER SOUNDS
As well as playing preloaded melodies and sounds,
dreamcube can also play any other song from your
mobile phone, tablet or computer.
To do this, connect the jack-jack audio cable with
the 3.5 mm connector that is supplied (13) to your
mobile device and the other end to the ‘LINE IN’
input on the projector.
When you do this, press the musical note button (2)
to play the sounds on your dreamcube. Press the
same button again to stop it playing.
Note 1:
In this case you have to adjust the volume
via your own mobile device.
Note 2:
If the sound activation mode is off,
the melodies and projections can be used
independently, so it will be up to users to use one or
the other according to their needs.
ENGLISH
