minicopter Diabolo 700 UL Скачать руководство пользователя страница 53

Страница: 53 / 60

Push the tail pushrod into the pushrod

holders D59, push the ball joint on the ball

of the tailservo arm and adjust the arm

rectangular. Attach a ball joint 041 on the

bellcrank D49 and adjust the bellcrank

also rectangular following the inner con-

tour of the bellcrank.Now place a mark

with a thin felt marker about 1mm before

the end of the ball joint and remove the

pushrod again.

Cut the tail pushrod with a Dremel or a

similar fast turning tool and attach now the

second threaded end in the pushrod on

the same way.

After hardening push the tail pushrod from

behind in the pushrod holders D59 and

turn a ball joint 041 at the front side on.

The numbers on the ball joints must show

away from the servoarm and the bellcrank.

Press in the front holes of the canopy on

each side a lense screw D99 with large

washers M3 004 and add inside a washer

shim 3x6x1 051.

Содержание Diabolo 700 UL





























































Результаты поиска

Содержание Diabolo 700 UL

Отзывы:

Бренды по названию

Популярные бренды

minicopter Diabolo 700 UL, Руководство пользователя

Результаты поиска

Содержание Diabolo 700 UL

Отзывы:

Бренды по названию

Популярные бренды