manualshive.com logo in svg

minicopter Diabolo 700 UL, Руководство пользователя

Поделиться
Скачать
minicopter Diabolo 700 UL Скачать руководство пользователя страница 39

Push the motor pinion D37 (18-22 teeth)

on the shaft so that one threaded hole is 

corresponding with the flat spot on the mo

-

tor shaft. Check for a clearance between 

pinion and motorplate of 0.5-1mm. Then 

tighten the pinion on the flat spot with a 

grub screw M4x5 035 using Loctite. Add 

then a second grub screw M4x5 035 using 

Loctite and tighten it.

Push the motor unit between the frames 

so that the motor cables are placed on the 

right side (seen in flight direction).

Mount the motor carrier D633 with four 

hex bolts M3x8 D197 and washers M3 

002 using Loctite.

Check the gear mesh. If you move the 

delrin wheel slightly in both directions you 

must feel a small play between the gear 

wheels. If the mesh is too small or too 

large then open the motor plate mounting 

screws again and move the motor a little 

bit. Then tighten the screws again.

Содержание Diabolo 700 UL





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды