Miniature Aircraft USA X-Cell Whiplash Turbine Скачать руководство пользователя

Страница: 24 / 38

Hardware for these

assemblies

Apply a small amount of

medium thread lock when

threading into metal parts

0018 x 2

M2 Lock Nut

• Install the magnets at the fan

using epoxy like UHU 300. Follow

instructions of the glue. One

mangent has to face by ‘N’ to the top

of the fan the other by ‘S’ (north and

south pole of magnet)

• Assemble fan hub to fan, then install

motor washer and hub on engine

and tighten MA0063 socket bolts a

little to clamp onto engine shaft.

• Next, install 131-118 washer and

nut (included with engine). Follow

manual of turbine engine. Now

tighten bolts 0063.Use a dial

indicator to verify runout of the hub

at the inner surface. It should be

less than +/- 0.015mm. If runout is

too big, repeat install procedure and

rotate hub by 90°.

• Install clutch (one-way bearing is

factory installed).

Assembly Tip

0081

0016-2

135-103

0018 x 2

0001 x 4

0049 x 2

0016-2 x 2

4mm Saftey Washer

0016-2

0080

0078-4

131-119

Motor Nut

(Included with motor)

131-118

131-117

131-120

4500-100

magnet (2x)

0064-3

0081 x 2

M4x16 Socket Bolt

0078-4 x 2

M4x6 Socket Bolt

0080 x 2

M4x14 Socket Bolt

0064-3 x 4

M3x6 Button Head

0049 x 2

M2x10 Socket Bolt

0001 x 4

2mm Washer

0063

Motor Washer

(Included with engine)

RPM sensor

and mount not

included to the kit

At youtube you can find a tutorial about how to setup and align

the turbine engine to correct position at the helicopter frame

https://www.youtube.com/watch?v=0mAdLoaoXks&t=102s

Содержание X-Cell Whiplash Turbine







































Результаты поиска

Содержание X-Cell Whiplash Turbine

Отзывы:

Похожие инструкции для X-Cell Whiplash Turbine

Бренды по названию

Популярные бренды

Miniature Aircraft USA X-Cell Whiplash Turbine, Руководство пользователя

Результаты поиска

Содержание X-Cell Whiplash Turbine

Отзывы:

Похожие инструкции для X-Cell Whiplash Turbine

Бренды по названию

Популярные бренды