Miniature Aircraft USA X-Cell Whiplash Turbine Скачать руководство пользователя

Страница: 9 / 38

Hardware for this

assembly

Assembly Tip

0107

0061

131-163

131-161

• The use of a light grease such as

MA3200-06 Tri-Flow Synthetic Grease

is required for damper/head axle

lubrication and O-rings

New damper system (131-490)

Hardware for this

assembly

0107 x 2

M3x6 Threaded

Steel Ball

0061 x 4

M3x8 Socket Head

Cap Screw

0086-1 x 2

M5x16 Flanged Bolt

0071 x 2

M3x18 Socket Bolt

0067 x 1

M3x14 Socket Bolt

120-7-1 x 2

M5x15 Safety Washer

131-183 x 2

9x14x.75 Washer

• The use of a light grease such

as MA3200-06 Tri-Flow Synthetic

Grease is required for thrust

bearing lubrication (pre-applied

and assembled from factory)

• 3 piece thrust bearing (MA131-

182) outer race with larger I.D.

(inside diameter) installs closest

to hub.

Assembly Tips

X 2

0086-1

120-7-1

Small

I.D.

Large

I.D.

131-183 131-181

131-182

131-183

131-181

Bearings Factory Installed

in Blade Grips

131-490

131-187

128-195

0067

0159

0597-4

128-314

0071

128-176

0869

0447-1

131-368

Factory Installed x 2

Apply

grease to

Head Axle

106-06

131-491

0447-1

Apply a small amount of

medium thread lock when

threading into metal parts

Factory Installed x 2

Содержание X-Cell Whiplash Turbine







































Результаты поиска

Содержание X-Cell Whiplash Turbine

Отзывы:

Похожие инструкции для X-Cell Whiplash Turbine

Бренды по названию

Популярные бренды

Miniature Aircraft USA X-Cell Whiplash Turbine, Руководство пользователя

Результаты поиска

Содержание X-Cell Whiplash Turbine

Отзывы:

Похожие инструкции для X-Cell Whiplash Turbine

Бренды по названию

Популярные бренды