MIMAKI Kebab MKII страница 32 Скачать руководство пользователя | Manualshive

Страница: 32 / 56

background image

Set a work

32

6

Set a work.

• Following the instruction on the screen, set a work at the

small diameter/ the large diameter setting position.

• Set the work at the left side of the origin position mark on the

bottom plate.

• When you need to draw several times to reduce the misalign-

ment of drawing, use the “work holder” and perform “origin
position mark detection”.
(

7

Press the

key.

• The work is set and the machine returns to the LOCAL mode by the

key.

• Set the start position of the drawing when setting the drawing origin of the work on the printer. (

• Detects the origin position mark when the detection function for the origin position mark is set to ON.

Attention when using a work of the different diameter from the previously used work

When using Kebab MkII system/Kebab MkII L system with UJF-3042 MkII/UJF-6042 MkII, if the using work is
changed as below, it is necessary to once remove Kebab MkII system/Kebab MkII L system and attach again after
adjusting the number of table sustaining shaft.

• As for the procedures for installation and disassembly, please read “Installation of Kebab MkII system”.

• When setting the work, make it may not touch the left/ the right side plate.

If you draw with the work touching the side plate, the work cannot rotate correctly.

• When you draw the work with a small diameter, remove the work holder; otherwise the work

holder and the slider may collide with each other.
(

Change the diameter of work

Change the number of sustaining shaft

less than 65 mm



65 mm or more

Change into 0 pc

65 mm or more



less than 65 mm

Change into 1 pc

Origin

position

mark

ENTER

END / POWER

«
...
30
31
32
33
34
...
»

Содержание Kebab MKII

























































Отзывы:

Нет отзывов

Похожие инструкции для Kebab MKII

Бренд: Zeka Страницы: 54

All in One Printer

Бренд: Xerox Страницы: 3

Бренд: V-King Страницы: 41

Бренд: Dascom Страницы: 12

Бренд: Dascom Страницы: 19

Бренд: Dascom Страницы: 5

Бренд: Panduit Страницы: 74

Бренд: Tally Страницы: 2

Бренд: Tally Dascom Страницы: 57

Бренд: Fenix Страницы: 65

Бренд: GCC Technologies Страницы: 63

Бренд: gCreate Страницы: 9

Бренд: GCC Technologies Страницы: 9

Бренд: GCC Technologies Страницы: 12

Бренд: gCreate Страницы: 21

Бренд: GCC Technologies Страницы: 199

Бренд: Xerox Страницы: 4

Бренд: Lexmark Страницы: 455

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды