MIMAKI Kebab MKII Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 56

background image

Installation of Kebab MkII system

12

Installation of Kebab MkII system

Attach Kebab MkII/Kebab MkII L system

Each of Kebab MkII/Kebab MkII L system is usable for the following printers respectively.

Attach Kebab MkII system on UJF-3042MkIIseries

Attach Kebab MkII system to UJF-3042MkIIseries matching its position with the diameter of the work drawn by the
UJF-3042MkII.

1

Turn OFF the main power of the printer main unit.

2

Open the front cover.

3

Remove the table by lifting up.

4

Depending on the diameter of the work,
use the sustaining shaft of the number
shown in the table.

Device Name

Corresponding Printer

Kebab MkII

UJF-3042MkII, UJF-3042MkII EX, UJF-3042MkIIe, UJF-3042MkIIe EX

Kebab MkII L

UJF-6042MkII, UJF-6042MkIIe

UJF-7151 plus, UJF-7151plusII

• Lift the table vertically by holding its both

edges.

Diameter of
work to use

Number of

sustaining shaft

more than 10 mm and less

than 65 mm

1 pc

65mm ~ 110mm

0 pc

«
...
10
11
12
13
14
...
»

Содержание Kebab MKII

























































Отзывы:

Нет отзывов

Похожие инструкции для Kebab MKII

Бренд: Oce Страницы: 192

Бренд: Oce Страницы: 22

Бренд: Oce Страницы: 41

Бренд: Oce Страницы: 28

Бренд: Oce Страницы: 6

Бренд: QMS Страницы: 104

Бренд: Oce Страницы: 386

Бренд: Oce Страницы: 2

Бренд: Oce Страницы: 27

Бренд: Oce Страницы: 324

Бренд: Canon Страницы: 358

Бренд: BIXOLON Страницы: 31

Бренд: Konica Minolta Страницы: 61

Бренд: Savin Страницы: 160

mC-Print3 MCP31LB

Бренд: Star Страницы: 12

3500DN - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 6

Бренд: Xerox Страницы: 2

Бренд: Oki Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды