Milwaukee MW806 MAX Скачать руководство пользователя страница 35

Страница: 35 / 52

EC / TDS

T.Ref.(ºC)

C.F.(cm

-1

)

ºC

ATC

mS/cm

MEASURE

25.3

2 5

12.20

1.0 0 0

C.F.(cm

-1

)

T.Coef.(%/ºC)

ºC

ATC

mS/cm

MEASURE

25.3

1.9 0

12.20

1.0 0 0

ºC

ATC

mS/cm

MEASURE

25.3

A U T O

12.20

R A N G E

To navigate the information displayed on the third LCD line, use

the



keys.

TIME

ºC

ATC

mS/cm

MEASURE

25.3

0 8:2 3:3 1

12.20

ºC

ATC

mS/cm

MEASURE

25.3

2 0.0 1.3 1

12.20

2 0

ºC

ATC

mS/cm

MEASURE

25.3

Y 9 5 %

12.20

B A T T E R

Readings can be temperature compensated.

Automatic Temperature Compensation (ATC), default:

The

probe has a built‑in temperature sensor; the temperature value

is used to automatically compensate the EC / TDS reading.
When in ATC mode, ATC tag is displayed and measurements

are compensated using the temperature coefficient.

Recommended default value for water samples is 1.90 %/°C.

Temperature compensation is referenced to the selected

reference temperature.

Use the



keys to view the current temperature coefficient.

The value is displayed along with the Cell Factor (C.F.) on the

third LCD line.

To change the temperature coefficient, see SETUP section

for details.
A temperature coefficient must also be set for the sample.

Note: If the reading is outside of range when the range is set

to automatic, the full‑scale value (20.00 mS/cm) is displayed

blinking.

Manual Temperature Compensation (MTC):

The temperature

value, shown on the second LCD line, can be manually set

using the



keys. When in MTC mode, the °C tag is blinking.

Note: Temperature‑compensation is configured in Setup.

Содержание MW806 MAX





















































Результаты поиска

Содержание MW806 MAX

Отзывы:

Похожие инструкции для MW806 MAX

Бренды по названию

Популярные бренды

Milwaukee MW806 MAX, Инструкция по эксплуатации

Результаты поиска

Содержание MW806 MAX

Отзывы:

Похожие инструкции для MW806 MAX

Бренды по названию

Популярные бренды