![background image](http://html.mh-extra.com/html/milwaukee/m12-fuel/m12-fuel_operators-manual_1797407006.webp)
5
1. Remove ALL dirt and debris found in the tank.
2. Remove the filter. Ensure that the float cage
remains in place.
Fuel Gauge
Starting and Stopping Vacuum
To turn the vacuum on
low
, push the switch to the
Speed One (I) position.
To turn the vacuum on
high
, push the switch to the
Speed Two (II) position.
To turn
the vacuum, push the switch to the OFF
(O) position.
Wet Pick-Up Operation
Float cage
3.
cage shuts suction when the tank is full.
Be sure that the
is clean and moves freely in
the
to ensure that the
works.
begin pick-up.
and
4. Turn on the vacuum
5.
a wet pick-up job or when tank is full and ready
to be emptied.
NOTE:
immediately and empty the tank.
6. Remove the battery pack.
7. Raise the hose to drain any excess liquid into
the tank.
8.
9. Clean the interior of the tank and pick-up acces-
sories periodically, more often when used to pick
up wet, sticky materials. Use warm, soapy water.
seats itself against a seal at the intake of the motor,
will develop a higher than normal pitch noise and the
the vacuum immediately.
To continue use, empty the liquid waste from the tank.
NOTE:
If the vacuum is accidentally tipped over, it
normal position.
OPERATION
WARNING
To reduce the risk of injury,
always wear proper eye
protection marked to comply with AS/NZS
1337.1.
When working in dusty situations, wear
appropriate respiratory protection or use a
suitable compliant dust extraction solution.
To reduce the risk of fire and injury, do not use
to pick up flammable or combustible materials.
Empty dust canister before use.
Before use, ensure the filter and float cage are
properly installed. Remove filter before all wet
pick-up operations.
To determine the amount of charge left in the
battery, turn the product
ON.
The Fuel Gauge will
light up for 2-3 seconds. When less than 10% of
charge is left, 1 light on the fuel gauge will flash 4
times.
To signal the end of charge, 1 light on the fuel gauge
will flash 8 times and the product will not run.
Charge the battery pack.
If the battery becomes too hot, the fuel gauge lights
will flash in an alternating pattern and the product
will not run. Allow the battery to cool down.
CAUTION
If the float is clean, moves freely,
and the suction does not shut off
when the tank is filled, contact a
MILWAUKEE
®
service facility for repairs. A malfunctioning
product can cause personal injury or property
damage.
For wet pick-up operation, it is recommended to use
the foam filter.
CAUTION
Failure to turn off product after float
rises and shuts off suction will result
in extensive damage to the motor.
Remove head and pour liquid waste into a
suitable drain.
•
Installing the Vacuum Hanger Mounting
Plate
The vacuum comes equipped with a hanger and
attachable mounting plate.
Position the mounting plate as desired, taking into
account the wall orientation.
-
face. An uneven surface could cause the mounting
plate to warp, resulting in possible problems when
installing vacuum.
Use the below recommended fasteners in the four
corner holes.
If installing into wood:
•
If installing into concrete:
• Use four suitable concrete anchors.
Storage
Install onto dimensional lumber 50mmx100mm
(2"x4") (or larger) or 19 mm (3/4") thick plywood.
Use four Ø 6 mm (1/4") x 30mm (1-1/4") lag
screws.
Before storing your vacuum, empty and clean the
tank, filter, and accessories. Remove the battery
pack.
WARNING
This machine is not suitable for
packing up hazardous dust.
CAUTION
If foam or liquid escapes from the
machine, switch off immediately.
WARNING
Clean the water level limiting
device regularly and examine it
for signs of damage.
Wet filters and the interior part of the liquid
container shall be dried before storage.
Содержание M12 Fuel
Страница 2: ......