24
25
ENGLISH
6825 MS ARNHEIM/6802 ED ARNHEIM
Netherlands
Winnenden, 2021-01-27
Alexander Krug
Managing Director
Authorized to compile the technical
fi
le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the
product described under “Technical Data” ful
fi
lls all the relevant
provisions of the following Regulations S.I. 2008/1597 (as amended),
S.I. 2017/1206 (as amended), S.I. 2012/3032 (as amended) and that
the following designated standards have been used:
BS EN 60745-1:2009+A11:2010
BS EN 60745-2-22:2011+A11:2013
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN 62479:2010
EN 301 489-1 V2.2.3
EN 301 489-17 V3.1.1
EN 300 328V2.2.2
BS EN IEC 63000:2018
Winnenden, 2021-01-27
Alexander Krug
Managing Director
Authorized to compile the technical
fi
le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on
the machine.
Please read the instructions carefully before starting
the machine.
Always wear goggles when using the machine.
Wear ear protectors!
Wear a suitable dust protection mask.
Wear gloves!
Do not use force.
Only for cutting work.
The guaranteed sound power level shown on this label
is 111 dB(A).
Do not swallow the coin cell battery!
Do not work on a ladder. Be sure to stand
fi
rmly.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose of electric tools together with
household waste material.
Electric tools and electronic equipment that have
reached the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
Check with your local authority or retailer for recycling
advice and collection point.
Rotation direction
n
Rated speed
V
Volts
Direct current
European Conformity Mark
British Confomity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH
Warning!
To reduce the risk of
fi
re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery pack or
charger in
fl
uid or allow a
fl
uid to
fl
ow inside them. Corrosive or
conductive
fl
uids, such as seawater, certain industrial chemicals, and
bleach or bleach containing products, etc., can cause a short circuit.
WARNING
This device contains a lithium button/coin cell battery. A
new or used battery can cause severe internal burns and lead to death
in as little as 2 hours if swallowed or enters the body. Always secure
the battery cover. If it does not close securely, stop using the device,
remove the batteries, and keep it away from children. If you think
batteries may have been swallowed or entered the body, seek
immediate medical attention.
SPECIFIED CONDITIONS OF USE
The cut-o
ff
machine is intended for cutting metal, stone and
ceramic materials.
Please refer to the instructions supplied by the accessory
manufacturer.
Do not use this product in any other way as stated for normal use.
WHEEL SELECTION
Cutting surface
Cutting disc type
Non-metallic materials
Silicone carbide abrasive
cutting disc
Metallic materials
Aluminum oxide abrasive
cutting disc
Masonry materials
Diamond wheel with water supply
or silicone carbide abrasive
cutting disc
WATER CONNECTION
A water connection is available on the tool to cool the wheel and
reduce the formation of dust. The water connection should be used on
all concrete cutting applications.
For best results, allow the water to coat the entire cutting wheel before
operation.
ONE-KEY™
To learn more about the ONE-KEY functionality for this tool, please
reference the Quick Start guide included with this product or go to
www.milwaukeetool.com/one-key. To download the ONE-KEY app, visit
the App Store or Google Play from your smart device.
Also, when the product experiences ESD, the Bluetooth
communication will be disconnected. It needs to be reset manually to
recover.
We considered the results to be within our minimum acceptable
performance level according to EN 55014-2 / EN 301489-1 / EN
301489-17.
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and ready to be
con
fi
gured via the ONE-KEY™ app.
Blinking Blue
Tool is actively communicating with the
ONE-KEY™ app.
Blinking Red
Tool is in security lockout and can be
unlocked by the owner via the ONE-
KEY™ app.
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk of
overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after used.
To obtain the longest possible battery life remove the battery pack from
the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away
from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION LI-ION BATTERY
The battery pack has overload protection that protects it from being
overloaded and helps to ensure long life.
Under extreme stress the battery electronics switch o
ff
the machine
automatically. To restart, switch the machine o
ff
and then on again. If
the machine does not start up again, the battery pack may have
discharged completely. In this case it must be recharged in the battery
charger.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation and
transport are exclusively to be carried out by appropriately trained
persons and the process has to be accompanied by corresponding
experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to
prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and spare parts. Should components
need to be replaced which have not been described, please contact
one of our Milwaukee service agents (see our list of guarantee/service
addresses).
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label and
order the drawing at your local service agents or directly at: Techtronic
Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the
product described under “Technical Data” ful
fi
lls all the relevant
regulations and the directives 2011/65/EU (RoHS), 2014/53/EU,
2006/42/EC, and the following harmonized standards have been used:
EN 60745-1:2009+A11:2010
EN 60745-2-22:2011+A11:2013
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN 62479:2010
EN 301 489-1 V2.2.3
EN 301 489-17 V3.1.1
EN 300 328V2.2.2
EN IEC 63000:2018
Measured sound power level: 109 dB(A)
Guaranteed sound power level: 111 dB(A).
Uncertainty K = 1,5 dB(A)
Conformity assessment procedure according 2000/14/EC to Annex VI.
Noti
fi
ed Body:
DEKRA Certi
fi
cation B.V. (0344)
Meander 1051/P.O.Box 5185
Содержание 4933471833
