Milnor MWF125J7 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 112

Milnor MWF125J7 Скачать руководство пользователя страница 30

Pellerin Milnor Corporation

Precaution

Explanation

Set the machine at the correct
height and level.

Use blocking to get the machine base level and the base pads a
minimum of 1” (25 mm) above the floor. Example:

Apply machinery grout evenly
so that support is distributed.

Fill all voids between the foundation and each base pad with in-
dustrial strength, non-shrinking grout. Allow the grout to fully
cure per the grout instructions.

Tighten anchors alternately so
that the hold-down force is
distributed.

Raise the machine slightly and remove the wood blocking. In-
stall a flat washer and nut on each anchor bolt and tighten in-
crementally in an alternating pattern. After tightening, check
each anchor at least twice.

4.

Technician Precautions

BNWUUI03.R03 0000257735 A.5 B.7 1/2/20 2:19 PM Released

CAUTION:

Overlooked or mishandled shipping restraints —

can cause costly ma-

chine damage.

�

Leave all internal shipping restraints in place until the machine is

anchored.

�

Check for and remove shipping tie wraps.

�

Check for and remove suspension hold-down hardware, if applicable.

�

Check for and remove red shipping brackets, if applicable.

�

See the “Cylinder inspection” warning and inspect the cylinder for smoothness.

Handling a Washer-extractor from Delivery to Final Location

26

«
...
28
29
30
31
32
...
»

Содержание MWF125J7

















































































































Отзывы:

Нет отзывов