Milnor 42044SR2 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 161

background image

12

Pellerin Milnor Corporation

�

Do not tamper with or disable any safety device or operate the machine with a mal-

functioning safety device. Request authorized service.

WARNING:

Electrocution and Electrical Burn Hazards —

Electric box doors—Op-

erating the machine with any electric box door unlocked can expose high
voltage conductors inside the box.

�

Do not unlock or open electric box doors.

WARNING:

Entangle and Crush Hazards —

Guards, covers, and panels—Operating

the machine with any guard, cover, or panel removed exposes moving
components.

�

Do not remove guards, covers, or panels.

Hazards Resulting from Damaged Mechanical Devices

BNWVUS04.C04 0000235090 A.3 A.2 A.4 12/11/20 8:32 AM Released

WARNING:

Multiple Hazards —

Operating a damaged machine can kill or injure per-

sonnel, further damage or destroy the machine, damage property, and/or

void the warranty.

�

Do not operate a damaged or malfunctioning machine. Request authorized service.

WARNING:

Explosion Hazards —

Cylinder—A damaged cylinder can rip apart dur-

ing extraction, puncturing the shell and discharging metal fragments at
high speed.

�

Do not operate the machine with any evidence of damage or

malfunction.

WARNING:

Explosion Hazards —

Inner door latches (divided cylinder machines)—A

damaged or improperly seated latch can cause the inner door to open dur-
ing operation, damaging the cylinder and shell. A damaged cylinder can
rip apart during extraction, puncturing the shell and discharging metal frag-
ments at high speed.

�

Ensure that the inner door is securely latched after loading and

unloading.

�

Do not operate the machine with any evidence of damage or malfunction.

WARNING:

Explosion Hazards —

Clutch and speed switch (multiple motor ma-

chines)—A damaged clutch or speed switch can permit the low speed mo-
tor to engage during extract. This will over-speed the motor and pulleys
and can cause them to rip apart, discharging metal fragments at high speed.

�

Stop the machine immediately if any of these conditions occur: • ab-

normal whining sound during extract • skidding sound as extract ends •
clutches remain engaged or re-engage during extract

General Service Information

«
...
12
13
14
15
16
...
»

Содержание 42044SR2


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 42044SR2

Бренд: Igloo Страницы: 1

Бренд: Caffitaly System Страницы: 40

Бренд: Blaupunkt Страницы: 80

Бренд: Oster Страницы: 16

Бренд: Kalorik Страницы: 24

Бренд: Metos Страницы: 42

Handheld Garment Steamer

Бренд: Jumbl Страницы: 2

Бренд: IKEA Страницы: 36

Бренд: Reer Страницы: 2

Бренд: Prestigio Страницы: 32

Бренд: Triomph Страницы: 33

Бренд: ZAKARIAN Страницы: 15

Бренд: Ninka Страницы: 68

Бренд: Green Star Страницы: 31

Oxidize It OX4000-A

Бренд: Oxidizer Pro Страницы: 12

Бренд: Kompernass Страницы: 37

Бренд: KBS Страницы: 30

Бренд: Hamilton Beach Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды