Milnor 42044SR2 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 161

background image

46

Pellerin Milnor Corporation

BNWUUM01 / 2019345

BNWUUM01

0000250244

C.2

11/7/19 10:43 AM

Released

Vibration Safety Switch Adjustments

BNWUUM01.C01 0000250243 A.3 C.2 1/2/20 2:19 PM Released

What the Vibration Safety Switch Does

BNWUUM01.C02 0000250242 A.3 C.2 1/2/20 2:19 PM Released

The

vibration safety switch

in

Figure 12: Vibration Switch, page 47

is an important safety fea-

ture. If properly adjusted, the switch will momentarily actuate as a result of repeated machine
movement caused by an out-of-balance condition.

below illustrates the effect of the

vi-

bration safety switch

actuation.

Table 17.

Effect of Tripping Vibration Safety Switch

Machine Model

Function of Vibration Safety Switch

30015, 30020, and 30022

Disables high speed extract

All microprocessor-controlled washer-extrac-
tors not listed above, and all dye machines

De-energizes three-wire relay, effectively ter-
minating machine operation

Adjustments

BNWUUM01.C03 0000250240 A.3 C.2 B.2 11/7/19 10:43 AM Released

When the machine leaves Milnor

®

, the actuator arm is tie-wrapped to prevent damage (except on

30015, 30020, and 30022 models).

This tie wrap must be removed after the machine is set in-

to position but before the machine is operated.

Adjustment of this switch from the factory setting is not recommended; however, it should be
checked for proper functioning and adjusted if its proper setting is lost.

As shown in

Figure 12: Vibration Switch, page 47

, the unit consists of a

sensitive micro-switch

with an extended actuating arm supporting an eccentric weight. The weight may be adjusted by
moving it up and down on the arm and by rotating it on the arm. In addition, the

micro-switch

it-

self may be tilted from side to side.

The sensitivity of the switch increases as the eccentric weight is raised on the actuating arm
and decreases as the weight is lowered.

The unit should be adjusted so that the actuating arm will always reset by itself, this being accom-
plished by rotating either the switch or the weight to give just enough bias to cause the switch to
reset. Check the adjustment by moving the arm to the left then slowly releasing it. Make sure the
micro-switch clicks when the arm is

slowly

released, thus indicating that it has reset. In the re-

leased position, the arm should rest

lightly

but definitely against the stop on the

micro-switch

case that prevents any further arm movement to the left.

Safety-Related Components & Assemblies

«
...
46
47
48
49
50
...
»

Содержание 42044SR2


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 42044SR2

BENT FRAME FIX RA

Бренд: Zline Страницы: 16

Бренд: Gasmate Страницы: 12

Бренд: Waring Страницы: 28

Бренд: Vitesse Home Страницы: 20

Element EL-BWC101-01

Бренд: Vinotemp Страницы: 22

Griddler Five GR-5 Series

Бренд: Cuisinart Страницы: 28

Бренд: Roller Grill Страницы: 32

Бренд: Bartscher Страницы: 61

Бренд: Aroma Professional Страницы: 104

Бренд: Simoniz Страницы: 8

Teasmade STM201N

Бренд: Swann Страницы: 8

Бренд: Hotpoint Страницы: 32

Бренд: GE Страницы: 7

Бренд: GE Страницы: 3

Бренд: GE Страницы: 12

Бренд: GE Страницы: 11

Бренд: GE Страницы: 12

Бренд: GE Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды