Millipore Integritest Exacta Скачать руководство пользователя страница 18

Страница: 18 / 284

Integritest



Exacta Filter Integrity Test Instrument

Operating and Maintenance Manual

Getting Started

IMPORTANT TASKS TO PERFORM BEFORE POWER UP

The Exacta instrument is designed to resist occasional splashing. It is not intended for use in

locations where accidental partial immersion in liquids may occur. The user should select a

location for the instrument with this in mind.

•

Make sure the instrument is on a stable surface.

•

Check your work area for safe operation.

•

Make sure that the ventilation slots on the bottom of the instrument are clear and free

from any obstructions.

Note:

Failure to provide proper ventilation may result in overheating and can damage

the instrument.

Note:

In locations prone to being wet, Millipore recommends the use of a Ground Fault

Interrupter Circuit (GFIC) for added user safety.

Power up

•

Connect the power cord to the instrument.

•

Turn on the instrument.

Note:

During power up, the instrument will display messages for entering the system

BIOS and Windows NT setup. These functions are for Millipore Service use only, and are not
accessible by the end user. For security purposes, the keyboard is locked during power up.

Note:

The 240 Volt power cord requires some assembly. A suitable power outlet

connector must be properly attached. Please ensure that a qualified electrician performs this
task.

Printer preparation

Put in a roll of paper.

Prime an Inkjet Ink Cartridge.

Install the Inkjet Cartridge.

Note:

Refer to the Printing Maintenance and Troubleshooting (page 146) for details.

Keyboard Features

The keyboard (Figure 1) and the glide plane are key elements for controlling all Integritest

Exacta software functions. Pressing the Tab or Enter key on the keyboard can be used to

move from one screen element to another. For most screens, pressing the Tab key is the

equivalent of pressing the Enter key or the left mouse button.

Содержание Integritest Exacta





























































































































































































































































































Результаты поиска

Содержание Integritest Exacta

Отзывы:

Бренды по названию

Популярные бренды

Millipore Integritest Exacta, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Integritest Exacta

Отзывы:

Бренды по названию

Популярные бренды