Millett NuHybrid Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 31

background image

15. Output bias adjustment

Set the DMM to measure DC volts, and position the leads of the DMM on TP1 and TP3 as
shown in the photo below. Adjust R18

, the “L Bias” potentiometer, to get a reading of about

11V.

Move the positive lead to TP2,

and adjust R17 (“R Bias”) to get about 11V again.

If you cannot adjust the pot to get to 11V, unplug power and go back and check everything
again.

Note that you can experiment with this setting to change the sound of the amp. There will be
no harm to the amp in setting this wherever you like.

«
...
24
25
26
27
28
...
»

Содержание NuHybrid
































Отзывы:

Нет отзывов

Похожие инструкции для NuHybrid

trans-nova 9505

Бренд: Hafler Страницы: 24

Бренд: Hafler Страницы: 9

Бренд: Hafler Страницы: 7

Бренд: Hafler Страницы: 21

Бренд: Hafler Страницы: 2

Бренд: Yamaha Страницы: 4

Бренд: Arcam Страницы: 15

Бренд: Prolude Amplification Страницы: 15

Бренд: dB Страницы: 6

Бренд: Burson Страницы: 8

1407A POWER AMPLIFIER

Бренд: Altec Lansing Страницы: 17

Бренд: Boss Audio Systems Страницы: 8

Бренд: Eden Страницы: 6

Бренд: NJS Страницы: 8

Бренд: Kicker Страницы: 20

Tube Location GA-9

Бренд: Gibson Страницы: 1

REFERENCE PHONO 10

Бренд: Audio Research Страницы: 18

Бренд: Klipsch Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды