Millett NuHybrid Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 31

background image

5. Install the small electrolytic capacitors

Install the smaller electrolytic capacitors. Be VERY careful that they are installed the correct
way - the PCB has a dot marking the positive terminal of the capacitors. The longer lead wire
is the positive terminal. Note that on the capacitor body, only the negative side is labeled

–

so the other side is positive. Insert them, bend the leads, solder and trim as before. Check
again that the orientation is correct:

«
...
12
13
14
15
16
...
»

Содержание NuHybrid
































Отзывы:

Нет отзывов

Похожие инструкции для NuHybrid

Бренд: JBL Страницы: 4

Бренд: NAD Страницы: 7

Бренд: TAG MCLAREN AUDIO Страницы: 17

Бренд: Ultimate Sound Страницы: 7

Crush PiX 50BXT

Бренд: ORANGE Страницы: 15

Бренд: Soldano Страницы: 8

Бренд: Gibson Страницы: 1

Бренд: Interface Devices Страницы: 8

Бренд: ORANGE Страницы: 13

MDi2 1K4-2K7-6K

Бренд: RAM Страницы: 13

Бренд: Harman Kardon Страницы: 11

Бренд: Ramsey Electronics Страницы: 36

Бренд: Vicon Страницы: 13

Бренд: Marantz Страницы: 17

The Prelude PC-200

Бренд: Harman Kardon Страницы: 6

Thunder TA Super TA7801

Бренд: MTX Страницы: 6

Бренд: Texas Instruments Страницы: 35

Kommander-KA Series

Бренд: K-array Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды