background image

© Miller Diving All Rights Reserved     Document # 030715001

3

DANGER:

 Diving with compressed breathing gas is a hazardous activity. Even if you do

everything right there is always the potential for serious injury or death. No one piece of diving
equipment can prevent the possibility that you may be injured or killed any time you enter the
water. We do not herein make any effort to teach the principles of diving. It is our assumption
the reader is a qualified diver.

Warranty Information

Miller Diving warrants every new helmet to be free from defects in workmanship for a period of ninety (90)

days from date of purchase. This warranty does not cover rubber parts or communications components.

Should any part become defective due to workmanship during the warranty period, contact your nearest autho-

rized  Miller dealer. If there is no dealer in your area, contact Miller Diving directly at (805) 965-8538, Fax (805)

966-5761, or E-Mail: [email protected]. You must have a return authorization number (RMA #) prior to

the return of any item. Upon approval from Miller Diving, return the defective part, freight prepaid to: Miller

Diving, 425 Garden Street, Santa Barbara, CA 93101, USA. The part will be repaired or replaced at no charge as

deemed necessary.

This warranty becomes null and void if:

1. The product is not registered with Miller Diving within ten (10) days of purchase.

2. The product has not been properly serviced and maintained according to this manual.

3. Unauthorized modifications have been made to the product.

4. The product has been abused or subjected to conditions which are unusual or exceed the product's
intended service.

Содержание MILLER 400 DIVING HELMET





























Отзывы: