Miller Bobcat 250 Diesel, Руководство пользователя

Страница: 9 / 80

OM-258413 Page 5
BATTERY CHARGING OUTPUT and BATTERY
EXPLOSION can injure.
Battery charging not present on all models.
D
Always wear a face shield, rubber gloves, and
protective clothing when working on a battery.
D
Stop engine before disconnecting or connecting battery cables,
battery charging cables (if applicable), or servicing battery.
D
Do not allow tools to cause sparks when working on a battery.
D
Do not use welder to charge batteries or jump start vehicles un-
less it has a battery charging feature designed for this purpose.
D
Observe correct polarity (+ and −) on batteries.
D
Disconnect negative (−) cable first and connect it last.
D
Keep sparks, flames, cigarettes, and other ignition sources
away from batteries. Batteries produce explosive gases during
normal operation and when being charged.
D
Follow battery manufacturer’s instructions when working on or
near a battery. See Battery Service Manual (listed in Safety
Standards) for additional information.
D
Have only qualified persons do battery charging work.
D
If battery is being removed from a vehicle for charging, discon-
nect negative (−) cable first and connect it last. To prevent an arc,
make sure all accessories are off.
D
Charge lead-acid batteries only. Do not use battery charger to
supply power to an extra-low-voltage electrical system or to
charge dry cell batteries.
D
Do not charge a frozen battery.
D
Do not use damaged charging cables.
D
Do not charge batteries in a closed area or where ventilation is
restricted.
D
Do not charge a battery that has loose terminals or one showing
damage such as a cracked case or cover.
D
Before charging battery, select correct charger voltage to match
battery voltage.
D
Set battery charging controls to the Off position before connect-
ing to battery. Do not allow battery charging clips to touch each
other.
D
Keep charging cables away from vehicle hood, door, or moving
parts.
HIGH PRESSURE FLUIDS can injure or kill.
D
Engine fuel system components can be under
high pressure.
D
Before working on fuel system, turn off engine
to release pressure.
D
If any fluid is injected into the skin or body seek medical help im-
mediately.
WELDING WIRE can injure.
D
Do not press gun trigger until instructed to do
so.
D
Do not point gun toward any part of the body,
other people, or any metal when threading
welding wire.
OVERUSE can cause OVERHEATING.
D
Allow cooling period; follow rated duty cycle.
D
Reduce current or reduce duty cycle before
starting to weld again.
D
Do not block or filter airflow to unit.
STATIC (ESD) can damage PC boards.
D
Put on grounded wrist strap BEFORE handling
boards or parts.
D
Use proper static-proof bags and boxes to
store, move, or ship PC boards.
TILTING OF TRAILER can injure.
D
Use tongue jack or blocks to support weight.
D
Properly install welding generator onto trailer
according to instructions supplied with trailer.
READ INSTRUCTIONS.
D
Read and follow all labels and the Owner’s
Manual carefully before installing, operating, or
servicing unit. Read the safety information at
the beginning of the manual and in each
section.
D
Use only genuine replacement parts from the manufacturer.
D
Perform installation, maintenance, and service according to the
Owner’s Manuals, industry standards, and national, state, and
local codes.
H.F. RADIATION can cause interference.
D
High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
D
Have only qualified persons familiar with electronic equipment
perform this installation.
D
The user is responsible for having a qualified electrician
promptly correct any interference problem resulting from the
installation.
D
If notified by the FCC about interference, stop using the
equipment at once.
D
Have the installation regularly checked and maintained.
D
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
ARC WELDING can cause interference.
D
Electromagnetic energy can interfere with
sensitive electronic equipment such as micro-
processors, computers, and computer-driven
equipment such as robots.
D
Be sure all equipment in the welding area is electromagnetically
compatible.
D
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
D
Locate welding operation 100 meters from any sensitive elec-
tronic equipment.
D
Be sure this welding machine is installed and grounded
according to this manual.
D
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.