Milazo Adult Bicycles, Инструкция по эксплуатации

Страница: 71 / 98

69 InstructIon Manual
If one pad is closer to the rim than the other, loosen the fixing nut at the back of the brake, apply
the brake to hold it centred, and retighten the fixing nut. Some brakes have a special mechanism
which enables you to set the clearance on either side of the rim using a screwdriver.
Brake pads should finally be adjusted so that the leading edge of the pad makes first contact with
the rim. Some brakes have special curved washers to allow this, but on less complex models it will
be necessary to apply a little force to the pad and its mounting.
Adjustment – Cantilever Calipers
Minor brake adjustment can be made via the barrel cable adjusters, which are located on each
brake lever. To adjust, squeeze the brake pads against the rim, loosen the lock nut, and turn the
adjusted to pull the brake pads closer to, or spread them away from the rim as required.
Brake pad clearance should be a maximum 2mm from the rim.
When correct re-tighten to lock-nut.
If the pads cannot be set close enough to the rim in this manner, you may have to adjust either
the length of the straddle cable or the length of the brake cable.
If the brakes use a separate brake cable and straddle cable, adjust the straddle length by first,
screwing the barrel adjuster ¾ of the way in, the loosening the straddle cable fixing bolt, then
pulling or pushing the cable through the fixing bolt to adjust the length, and finally re-tightening
the fixing bolt.
Check that the straddle bridge is in the middle of the cable to ensure even brake pad contact.
Apply full force to the brake lever to test, then fine tune using the barrel adjuster.
To adjust the brake cable length, loosen the brake cable-fixing bolt on the cable straddle bridge,
adjust the length until the brake shoes are the correct distance from the rim, then re-tighten
and test.
PBLF/0 9
PACIFIC BRANDS SPORT & LEISURE PTY LTD ABN 53 098 742 708
55
Brake pads should finally be adjusted so that the leading edge of the
pad makes first contact with the rim. Some brakes have special curved
washers to allow this, but on less complex models it will be necessary
to apply a little force to the pad and its mounting.
Adjustment - Cantilever Calipers
Minor brake adjustment can be made via the barrel cable adjusters
which are located on each brake lever. To adjust, squeeze the brake
pads against the rim, loosen the lock nut, and turn the adjuster to pull
the brake pads closer to, or spread them away from the rim as
required.
Brake pad clearance should be a maximum 2mm from the rim.
When correct re-tighten the lock nut.
If the pads cannot be set close enough to the rim in this manner, you
may have to adjust either the length of the straddle cable
or the length of the brake cable.
If the brakes use a separate brake cable and straddle cable, adjust the
straddle length by first, screwing the barrel adjuster 3/4 of the way in, then
loosening the straddle cable fixing bolt, then pulling or pushing the cable
through the fixing bolt to adjust the length, and finally re-tightening the fix-
ing bolt.
Check that the straddle bridge is in the middle of the cable to ensure
even brake pad contact. Apply full force to the brake lever to test, then fine
tune using the barrel adjuster.
To adjust the brake cable length, loosen the brake cable fixing bolt on
the cable straddle bridge, adjust the length until the brake shoes are the
correct distance from the rim, then re-tighten and test.
Link Cable
Quick Release Hook
Brake Cable
Anchor Bolt
2mm clearance
Parallel
Parallel
Curved
Adjustment
Washers
10mm Spanner
Fully adjustable type brake shoes
5mm Allen Key
After Adjustment, securely tighten brake shoe holding nut or bolt
20067_OWNERS-MANUAL.qxp 08/03/2006 10:41 AM Page 55
PBLF/0 9 PACIFIC BRANDS SPORT & LEISURE PTY LTD ABN 53 098 742 708
55
Brake pads should finally be adjusted so that the leading edge of the
pad makes first contact with the rim. Some brakes have special curved
washers to allow this, but on less complex models it will be necessary
to apply a little force to the pad and its mounting.
Adjustment - Cantilever Calipers
Minor brake adjustment can be made via the barrel cable adjusters
which are located on each brake lever. To adjust, squeeze the brake
pads against the rim, loosen the lock nut, and turn the adjuster to pull
the brake pads closer to, or spread them away from the rim as
required.
Brake pad clearance should be a maximum 2mm from the rim.
When correct re-tighten the lock nut.
If the pads cannot be set close enough to the rim in this manner, you
may have to adjust either the length of the straddle cable
or the length of the brake cable.
If the brakes use a separate brake cable and straddle cable, adjust the
straddle length by first, screwing the barrel adjuster 3/4 of the way in, then
loosening the straddle cable fixing bolt, then pulling or pushing the cable
through the fixing bolt to adjust the length, and finally re-tightening the fix-
ing bolt.
Check that the straddle bridge is in the middle of the cable to ensure
even brake pad contact. Apply full force to the brake lever to test, then fine
tune using the barrel adjuster.
To adjust the brake cable length, loosen the brake cable fixing bolt on
the cable straddle bridge, adjust the length until the brake shoes are the
correct distance from the rim, then re-tighten and test.
Link Cable
Quick Release Hook
Brake Cable
Anchor Bolt
2mm clearance
Parallel
Parallel
Curved
Adjustment
Washers
10mm Spanner
Fully adjustable type brake shoes
5mm Allen Key
After Adjustment, securely tighten brake shoe holding nut or bolt
20067_OWNERS-MANUAL.qxp 08/03/2006 10:41 AM Page 55
PBLF/0 9 PACIFIC BRANDS SPORT & LEISURE PTY LTD ABN 53 098 742 708
55
Brake pads should finally be adjusted so that the leading edge of the
pad makes first contact with the rim. Some brakes have special curved
washers to allow this, but on less complex models it will be necessary
to apply a little force to the pad and its mounting.
Adjustment - Cantilever Calipers
Minor brake adjustment can be made via the barrel cable adjusters
which are located on each brake lever. To adjust, squeeze the brake
pads against the rim, loosen the lock nut, and turn the adjuster to pull
the brake pads closer to, or spread them away from the rim as
required.
Brake pad clearance should be a maximum 2mm from the rim.
When correct re-tighten the lock nut.
If the pads cannot be set close enough to the rim in this manner, you
may have to adjust either the length of the straddle cable
or the length of the brake cable.
If the brakes use a separate brake cable and straddle cable, adjust the
straddle length by first, screwing the barrel adjuster 3/4 of the way in, then
loosening the straddle cable fixing bolt, then pulling or pushing the cable
through the fixing bolt to adjust the length, and finally re-tightening the fix-
ing bolt.
Check that the straddle bridge is in the middle of the cable to ensure
even brake pad contact. Apply full force to the brake lever to test, then fine
tune using the barrel adjuster.
To adjust the brake cable length, loosen the brake cable fixing bolt on
the cable straddle bridge, adjust the length until the brake shoes are the
correct distance from the rim, then re-tighten and test.
Link Cable
Quick Release Hook
Brake Cable
Anchor Bolt
2mm clearance
Parallel
Parallel
Curved
Adjustment
Washers
10mm Spanner
Fully adjustable type brake shoes
5mm Allen Key
After Adjustment, securely tighten brake shoe holding nut or bolt
20067_OWNERS-MANUAL.qxp 08/03/2006 10:41 AM Page 55
Detailed maintenance