Milazo Adult Bicycles, Инструкция по эксплуатации

Страница: 21 / 98

19 InstructIon Manual
The seat pillar must be inserted so that the minimum insertion mark
cannot be seen.
The right and left pedals each have a different thread. They are NOT
interchangeable.
Never force pedal into an incorrect crank arm.
Attachment of an incorrect pedal into a crank arm will cause irreparable damage.
42
ASSEMBL
Y
Seat
Loosen nut on the seat clamp and add 3 or 4 drops of oil onto the
threads of the bolt. Place the smaller end of the seat post into the seat
clamp until it stops with the bolt to the rear of the seat post. Thread the
nut on the seat clamp loosely. Insert the larger end of the seat post into
the seat tube of the bicycle frame observing the minimum insertion mark
on the seat post. Position the top surface of the seat parallel with the
ground. The serrations on the seat clamp must mesh completely with the
seat frame serrations, push the front of the seat up and down to align the ser-
rations. Securely tighten the seat clamp. Securely tighten the bolts
on the seat post clamp. If your bicycle is equipped with a quick release,
refer to page 56 for proper adjustment instructions.
Pedals & Crank Set
Check for the right (R, red) stricker and left (L, green) sticker on each pedal
and crank arm. Match the appropriate pedal to each crank (right to right and
left to left) for assembly. Start each pedal spindle by hand to avoid stripping
the threads. Tighten with a 15mm narrow open ended wrench so that the
shoulder of the spindle is securely tightened against the crank arm. Note that
the right hand pedal attaches to the chainwheel side crank arm with a right-
hand (clockwise) thread. The left pedal attaches to the other crank arm and
has a left-hand (counter-clockwise) thread. It is very important that you check
the crank set for correct adjustment and tightness before riding your bicycle.
New cranks may become loose with initial use, refer to p.87-89 for proper
crank set adjustment and maintenance. Once the pedals have been attached,
check that the crank arm rotates smoothly and that there is no lateral move-
ment.
The seat post must be inserted so that the minimum
insertion mark cannot be seen.
Attachment of an incorrect pedal into a crank
arm will cause irreparable damage.
seat
1 Insert the smaller end of the seat pillar into the seat clamp and tighten.
2 Insert the seat / pillar assemble into the frame tube of the bicycle observing the minimum
insertion mark on the pillar.
3 Tighten with a spanner or torque wrench.
4 The bicycle may be equipped with seat binder bolt or quick release (QR), please refer to seat
section in the detail maintainance in this manual.
Pedals
1 attach the pedals and tighten with a 15mm narrow
open-ended spanner. note that the right hand pedal attaches to the chain wheel side crank
with a right hand (clockwise) thread. the left pedal attaches to the other crank arm and has
a left hand (counter clockwise) thread.
2 the ends of each pedal spindle are marked with either
an ‘r’ for right or ‘l’ for left.
ASSEMBLY
42
ASSEMBL
Y
Seat
Loosen nut on the seat clamp and add 3 or 4 drops of oil onto the
threads of the bolt. Place the smaller end of the seat post into the seat
clamp until it stops with the bolt to the rear of the seat post. Thread the
nut on the seat clamp loosely. Insert the larger end of the seat post into
the seat tube of the bicycle frame observing the minimum insertion mark
on the seat post. Position the top surface of the seat parallel with the
ground. The serrations on the seat clamp must mesh completely with the
seat frame serrations, push the front of the seat up and down to align the ser-
rations. Securely tighten the seat clamp. Securely tighten the bolts
on the seat post clamp. If your bicycle is equipped with a quick release,
refer to page 56 for proper adjustment instructions.
Pedals & Crank Set
Check for the right (R, red) stricker and left (L, green) sticker on each pedal
and crank arm. Match the appropriate pedal to each crank (right to right and
left to left) for assembly. Start each pedal spindle by hand to avoid stripping
the threads. Tighten with a 15mm narrow open ended wrench so that the
shoulder of the spindle is securely tightened against the crank arm. Note that
the right hand pedal attaches to the chainwheel side crank arm with a right-
hand (clockwise) thread. The left pedal attaches to the other crank arm and
has a left-hand (counter-clockwise) thread. It is very important that you check
the crank set for correct adjustment and tightness before riding your bicycle.
New cranks may become loose with initial use, refer to p.87-89 for proper
crank set adjustment and maintenance. Once the pedals have been attached,
check that the crank arm rotates smoothly and that there is no lateral move-
ment.
The seat post must be inserted so that the minimum
insertion mark cannot be seen.
Attachment of an incorrect pedal into a crank
arm will cause irreparable damage.
Insert left
Pedal only
Insert right
Pedal only