Miele WDA 210 WPM Скачать руководство пользователя страница 21

Страница: 21 / 72

5. Adding detergent

It is important to dispense the correct

amount, because . . .
. . . too little detergent results in:

– laundry not getting properly clean

and with time it may become grey

and hard to the touch.

– greasy particles clinging to the laun‐

dry.

– limescale deposits on the heater ele‐

ments.

. . . too much results in:

– excessive foam which causes a low

level of agitation and poor wash,

rinse and spin results.

– high water consumption (an addition‐

al rinse cycle will automatically

switch in).

– a burden to the environment.



Pull out the detergent drawer and

add detergent to the compartments.



Detergent for the pre-wash (divide the

total recommended amount as follows:
add

to compartment



and

compartment



)



Detergent for the main wash, including

Soak if selected



Fabric softener or liquid starch



Close the detergent dispenser draw‐

er.

Useful tip:

See "Detergent" for further

information.

Содержание WDA 210 WPM









































































Результаты поиска

Содержание WDA 210 WPM

Отзывы:

Похожие инструкции для WDA 210 WPM

Бренды по названию

Популярные бренды

Miele WDA 210 WPM, Руководство по эксплуатации

Результаты поиска

Содержание WDA 210 WPM

Отзывы:

Похожие инструкции для WDA 210 WPM

Бренды по названию

Популярные бренды