Miele TMG 440 WP Скачать руководство пользователя страница 79

Страница: 79 / 84

Settings menu

Code

The code prevents your dryer being

used without your knowledge.

Options

– Activate

The code is 250 and can be

activated.

When the code has been activated,

you have to enter the code after

switching the dryer on. Otherwise the

dryer cannot be operated.

– Deactivate

For using the dryer without entering

the code. This only appears if the

code has been activated previously.

– Change

You can enter a code of your own.



Important. Make a note of your

new code. If you forget the code, the

dryer will need to be unlocked by the

Miele Service Department.

Display brightness

The brightness of the display can be

altered.

The setting selected is shown in a bar

chart.

Factory default: a medium setting.

– Darker

      

– Brighter

      

You will see the brightness change as

the setting is selected.

Dark display

To save energy the display and

buttons will go out after 10 minutes

and the

Start/Stop

button will flash

slowly. You can alter this setting.

Options

– On (factory default)

The display will go out (after 10

minutes):

– if a programme is not selected

after the dryer has been

switched on

– during the current programme
– after the end of a programme.

– On (not in current programme)

The display will go out (as described

above) but will remain on while the

programme is running.

– Off

The display will remain on (i.e. it will

never go out).

You can switch the display and buttons

back on again by pressing any button.

Содержание TMG 440 WP





















































































Результаты поиска

Содержание TMG 440 WP

Отзывы:

Похожие инструкции для TMG 440 WP

Бренды по названию

Популярные бренды

Miele TMG 440 WP, Руководство по эксплуатации

Результаты поиска

Содержание TMG 440 WP

Отзывы:

Похожие инструкции для TMG 440 WP

Бренды по названию

Популярные бренды