Miele TMG 440 WP Скачать руководство пользователя страница 46

Страница: 46 / 84

Fragrance flacon

Using a fragrance flacon (optional

accessory) will add a pleasant

fragrance to your laundry.



Before using a fragrance flacon,

please read "Warning and safety

instructions - Using a fragrance

flacon (optional accessory)".

Inserting a fragrance flacon

Only hold the fragrance flacon as

illustrated. Do not hold it at an angle

or tip it as the fragrance will run out

of the flacon.



Hold the flacon securely to prevent

opening it by mistake.



Pull off the protective seal.



Open the door of the tumble dryer.

The fragrance flacon is inserted in the

upper fluff filter in the opening on the

right hand side beside the grip.

If you are not using a fragrance

flacon: the cover must always remain

closed (push the cover down

completely with the tab).



Open the cover using the tab until the

tab is at the top right hand side as

shown.



Insert the flacon in the opening as far

as it will go.

Содержание TMG 440 WP





















































































Результаты поиска

Содержание TMG 440 WP

Отзывы:

Похожие инструкции для TMG 440 WP

Бренды по названию

Популярные бренды

Miele TMG 440 WP, Руководство по эксплуатации

Результаты поиска

Содержание TMG 440 WP

Отзывы:

Похожие инструкции для TMG 440 WP

Бренды по названию

Популярные бренды