Miele TMG 440 WP Скачать руководство пользователя страница 50

Страница: 50 / 84

Problem solving guide

With the help of the following notes minor faults in the performance of the

appliance, some of which may result from incorrect operation, can be put right

without contacting the Service Department.



Repair work to electrical appliances should only be carried out by a suitably

qualified person in strict accordance with current local and national safety

regulations. Repairs and other work by unqualified persons could be

dangerous. The manufacturer cannot be held liable for unauthorised work.

Some of the messages in the display are more than one line long. Touch the





sensor to read them in full.

Messages in the display

Problem

Cause and remedy



lights up after

switching on

Access via a code has been activated.



See "Settings menu, Code".



Adjust the load See 

lights up after a

programme is cancelled

This is not a fault.

In some programmes, if the drum has been

underloaded or is empty, the programme will be

cancelled. This can also happen if the items are

already dry.



Open and close the door to resume drying.



Dry individual items using the

Warm air

timed

drying programme.



 Service Fault F

lights up after a

programme is cancelled

No obvious cause.



Switch the dryer off and then on again.



Start a programme.

If the programme is cancelled again and an error

message appears, there is a fault. Contact the Miele

Service Department.

Содержание TMG 440 WP





















































































Результаты поиска

Содержание TMG 440 WP

Отзывы:

Похожие инструкции для TMG 440 WP

Бренды по названию

Популярные бренды

Miele TMG 440 WP, Руководство по эксплуатации

Результаты поиска

Содержание TMG 440 WP

Отзывы:

Похожие инструкции для TMG 440 WP

Бренды по названию

Популярные бренды