Miele T 8861 WP Edition 111 Скачать руководство пользователя страница 52

Страница: 52 / 64

The system lock prevents your
machine being used without your
knowledge.

You can switch on the system lock if
required.

The dryer's electronics are then locked.
The dryer can still be switched on but a
programme cannot be started.

– If an attempt is made to start a

programme, the indicator light for the

Gentle tumble

button will come on

and the key symbol

0-§

will appear

in the display.

The door is not locked and can be
opened at any time.

Locking

Before you begin, first ensure that:

– The dryer is switched off.

– The door is closed.

Press the

Gentle tumble

button and

keep it pressed in up to step

Press the

button.

The

Automatic plus

indicator light will

come on.

Slowly turn the programme selector

three positions stage by stage in a
clockwise direction.
Each of the three programme
indicator lights must come on one
after the other.

Now slowly turn the programme

selector six positions stage by stage
in an anti-clockwise direction.
Each of the six programme indicator
lights must come on one after the
other.

The indicator light for the

Gentle tumble

button will flash and a key symbol

0-§

will appear in the display.

Release the

Gentle tumble

button.

The system lock is activated.

Switch the dryer off.

Deactivating the system lock

Before you begin, first ensure that:

– The dryer is switched off.

– The door is closed.

The procedure is the same as for
activating the lock. Repeat steps

At step

the indicator light for the

Gentle tumble

button will stop flashing

and the key symbol

0-§

will go out.

The electronics are no longer locked.

Electronic system lock

Содержание T 8861 WP Edition 111

































































Результаты поиска

Содержание T 8861 WP Edition 111

Отзывы:

Похожие инструкции для T 8861 WP Edition 111

Бренды по названию

Популярные бренды

Miele T 8861 WP Edition 111, Руководство по эксплуатации

Результаты поиска

Содержание T 8861 WP Edition 111

Отзывы:

Похожие инструкции для T 8861 WP Edition 111

Бренды по названию

Популярные бренды