Miele T 8861 WP Edition 111 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 64

background image

The following information appears in
the display:

– Programme duration

– Programme sequence

Drying
Cooling down
Finish

– Check and fault messages

The following can be set via the
display:

– Programme duration for

Warm air

– Delay start

You can set a programme to start
automatically at a later time.

– Programmable functions

The programmable functions are
used to alter the machine's
electronics to suit changing
requirements. See "Programmable
functions" later in this booklet for
more details.

Perfect Dry indicator light

The Perfect Dry system measures the
laundry's residual moisture in
programmes with drying levels and
provides a more precise drying result.
After starting the programme, the
electronics will measure the duration of
the programme (Estimated time
remaining). The

Perfect Dry

indicator

light will flash during this time.
The programme duration will be shown
after a short time and the indicator light
will go out.
Once the selected drying level has
been reached, the

Perfect Dry

indicator

light will remain on until the end of the
programme.

The

Perfect Dry

indicator light remains

dark during the following time
controlled programmes:

Woollens,

Warm air, Gentle smoothing

.

Estimated time remaining

The expected time will automatically be
displayed (Estimated time remaining).
The following factors all affect the
estimated time remaining: residual
moisture content after spinning; type of
fabric; size of load; room temperature
or fluctuations in the power supply.
The electronics continually assess
conditions in the tumble dryer and
adjust the estimated time remaining for
a more accurate reading. Because of
this, the time displayed can alter during
the course of a programme.
In the same way, programmes may
finish early. This can happen with
particularly fine fabrics, very small
loads or if items were partly dry
beforehand.

Before using for the first time

,

Install and connect the tumble

dryer according to the descriptions
in these operating instructions. If the
tumble dryer has not been
transported as described, then it
must be left to stand for at least 1
hour before it is connected to the
electricity supply.

Operating the tumble dryer

16

«
...
14
15
16
17
18
...
»

Содержание T 8861 WP Edition 111

































































Отзывы:

Нет отзывов

Похожие инструкции для T 8861 WP Edition 111

Бренд: ziltek Страницы: 6

Бренд: Emerald Страницы: 32

Бренд: Amica Страницы: 52

Бренд: nedis Страницы: 108

Бренд: Vulcan-Hart Страницы: 28

Global Design 815U

Бренд: Toastmaster Страницы: 16

Бренд: e-Ware Страницы: 4

Cook Mate AF-D50-004A

Бренд: HAEGER Страницы: 64

Бренд: Klarstein Страницы: 76

Бренд: BOMANN Страницы: 24

Бренд: Bosch Страницы: 36

Бренд: Bosch Страницы: 36

Бренд: Bosch Страницы: 44

Бренд: Bosch Страницы: 36

Бренд: Bosch Страницы: 40

Бренд: Bosch Страницы: 40

Бренд: Bosch Страницы: 36

Бренд: Bosch Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды