Miele T 15 Series Скачать руководство пользователя страница 38

Страница: 38 / 42

Technical Information

T 15xx Dryers

The “Anti-crease” LED is FLASHING - Fault stored. Proceed to “Access”
steps below.

Access (retrieval):

1.  Access the service mode. See Section 6.1.2.
2.  Turn the selector switch to “Woolens”.
3.  Press the

Start

button.

4.  Note the illuminated LEDs.
5.  Refer to Table 6-3 to determine the stored fault.
6.  Switch the appliance off.
7.  Perform the necessary service steps to rectify the cause of the fault, then

proceed to “Delete a Stored Fault Code” below.

LED(s) Lit Steadily

Component

Rotary iron

Fan NTC open circuit

Hand iron

NTC at heater bank open circuit

Normal

NTC at heater bank short circuit

Rotary iron & Hand iron

Fan NTC short circuit

Normal and Rotary iron

Maximum drying time (180 minutes) exceeded

Table 6-3:

T 1576 Fault Codes

Delete a stored fault code:

1.  Access the service mode. See Section 6.1.2.
2.  Turn the selector switch to “Woolens”.
3.  Press the

Start

button.

4. Press and hold the

Gentle

button.

5. Press the

Start

button.

6. Release the

Gentle

button. The appropriate LED turns off.

7. Switch the appliance off.

6.3

Programming Mode (T 1576 Only)

Accessing:

1.  Switch the appliance off.
2.  Turn the program selector switch to 12 o’clock.
3.  Press and hold the

Gentle

and

Buzzer

buttons.

4. Switch the appliance on.
5. Release the buttons.

Acknowledgement indicator:

The “Drying” and “Cooling down” LEDs flash to indicate that programming mode
is active.

Navigation:

1. Turn the program selector switch to the desired position; press

Start

activate the function.

2. The programmed option is indicated by the status of the “Rotary iron” LED.

Содержание T 15 Series











































Результаты поиска

Содержание T 15 Series

Отзывы:

Бренды по названию

Популярные бренды

Miele T 15 Series, Техническая информация

Результаты поиска

Содержание T 15 Series

Отзывы:

Бренды по названию

Популярные бренды