Miele T 15 Series Скачать руководство пользователя страница 36

Страница: 36 / 42

Technical Information

T 15xx Dryers

6.0

Fault Diagnosis

6.1

Service Mode

6.1.1

T 1515, T 1520, T 1526, T 1565 C and T 1570 C

Accessing:

1.  Switch the appliance off.
2.  Release all pushbuttons.
3.  Turn the program selector switch to the “Finish” (12 o’clock) position.
4.  Switch the appliance on.
5.  Press and release the

Load size

button (or

Buzzer

button, depending on

model) 3 times in quick succession within 10 seconds.

Acknowledgement indicator:

The “Drying” LED flashes to show that service mode is activated.

Navigation:

Refer to Table 6-1. Turn the program selector switch to the desired position, then
press

Start

To exit service mode, switch the appliance

off

Selector Switch Position

Function

Finish

Buzzer pushbutton test

COTTONS Extra dry

Heater on

COTTONS

Drum drives left (vented models only)

COTTONS Normal

Buzzer activated

COTTONS Hand iron

Drum drives right (vented models only)

COTTONS Hand iron

Condenser fan (condenser models only)

COTTONS Machine iron

Condensate pump (condenser models only)

15 mins. cool air

Residual moisture sensor test; see Section 6.4

20 mins. warm air

Residual moisture sensor test; see Section 6.4

PERMANENT PRESS Hand iron LED test (LEDs illuminated)

PERMANENT PRESS

Dryer type. Continuous tone = vented;
intermittent tone = condenser.

Table 6-1:

Service Mode Functions (T 1515, T 1520, T 1526, T 1565 C, T 1570 C)

Содержание T 15 Series











































Результаты поиска

Содержание T 15 Series

Отзывы:

Бренды по названию

Популярные бренды

Miele T 15 Series, Техническая информация

Результаты поиска

Содержание T 15 Series

Отзывы:

Бренды по названию

Популярные бренды