Miele T 15 Series Скачать руководство пользователя страница 37

Страница: 37 / 42

Technical Information

T 15xx Dryers

6.1.2

T 1576

Accessing:

1.  Switch the appliance off.
2.  Turn the program selector switch to 12 o’clock.
3.  Press and hold the

Gentle

and

Start

buttons.

4. Switch the appliance on.
5. Release the buttons.

Acknowledgement indicator:

The “Drying” LED flashes to show that service mode is activated.

Navigation:

Refer to Table 6-2. Turn the program selector switch to the desired position, then
press

Start

To exit the service mode, switch the appliance

off

Selector Switch Position

Press Start to Activate…

COTTONS Extra dry

Main motor operates 10 seconds in each direction

COTTONS

Vacant

COTTONS Normal

One heater and main motor operate

COTTONS Hand iron

Main motor operates

COTTONS Hand iron

Both heaters and main motor operate

COTTONS Rotary iron

Residual moisture
sensor test

“Cooling down” lights up = OK
“Cooling down” flashes = fault

Fluff

Residual moisture
sensor test

“Cooling down” lights up = OK
“Cooling down” flashes = fault

20 mins.

LED test

Line Dry

Button test

Woolens

Fault codes (see Section 6.2)

PERMA PRESS Hand iron Vacant

PERMA PRESS Normal

Vacant

PERMA PRESS

Vacant

Table 6-2:

Service Mode Functions (T 1576)

6.2

Fault Codes (T 1576 Only)

Initial requirements:

1.  Switch the appliance on.
2.  Turn the selector switch to the “COTTONS Extra dry” position.
3.  Press the

Start

button to begin the program.

4. Note the status of the “Anti-crease” LED:

The “Anti-crease” LED is lit STEADILY - No faults stored.

Содержание T 15 Series











































Результаты поиска

Содержание T 15 Series

Отзывы:

Бренды по названию

Популярные бренды

Miele T 15 Series, Техническая информация

Результаты поиска

Содержание T 15 Series

Отзывы:

Бренды по названию

Популярные бренды