Miele SmartLine CSDA 7000 FL Скачать руководство пользователя страница 46

Страница: 46 / 56

Installation

Installing the downdraft
extractor

The downdraft extractor can be
installed with the connector for the air
duct on either the right or the left-hand
side.

Connector for air duct on the right

Connector for air duct on the left



Stick the supplied sealing strip under
the edge of the cover. Do not apply
the sealing strip under tension.



Fit the clips onto the spacer bars.



Guide the control cable downwards
between the spacer bars.



Fit the cover onto the spacer bars.



Remove the moisture collection tray
from the casing.



Fasten the casing from the inside with
the screws



on the right and left



sides (3 in each case).



Fasten the moisture collection tray.



Mount the air duct.

Ensure that the air duct is not under
mechanical tension after installation!

Содержание SmartLine CSDA 7000 FL

























































Результаты поиска

Содержание SmartLine CSDA 7000 FL

Отзывы:

Похожие инструкции для SmartLine CSDA 7000 FL

Бренды по названию

Популярные бренды

Miele SmartLine CSDA 7000 FL, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание SmartLine CSDA 7000 FL

Отзывы:

Похожие инструкции для SmartLine CSDA 7000 FL

Бренды по названию

Популярные бренды