Miele PWD 8545 AD Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 48

Miele PWD 8545 AD Скачать руководство пользователя страница 30

MACHINE STATUS

REV.0.00_COD.223130_A4

Page 30

9.

MACHINE STATUS

9.1

Preparation

When the machine is switched on, the internal tank is automatically filled with water. The machine
is ready for use once a certain water level is reached.

9.2

Ready for operation

The machine is ready for operation.

The diagnostics are active.

If necessary the display indicates that the door is open or gives warning messages:

Lack of detergent, lack of descaling agent, memory full (historical data) or high temperature inside
chamber.

9.3

Malfunctioning



In the event that an error is detected, the cycle is interrupted and the door remains locked.



The error message appears in the display.



The door remains locked.

To open the door, the door release sequence must be performed at the controls:



Press START



and STOP



simultaneously for 3 seconds.



Select STANDARD



and SHORT



one after the other.



After the door opening sequence, the machine is READY FOR OPERATION and the door
can be opened.

If the error persists or the door remains closed, contact Service or a suitably qualified person.

9.4

Interruption to the power supply during operation

If a temporary interruption to the power supply occurs during a programme, no particular action is
required.

The programme will continue after the interruption.

«
...
28
29
30
31
32
...
»

Содержание PWD 8545 AD

















































Отзывы:

Нет отзывов