Miele PW 5105 Vario Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 60

background image

The door will not open

Possible cause

Remedy

The door is locked after
a programme has been
cancelled.

For safety reasons the drum door cannot be opened
if the suds temperature is higher than 50°C. Wait
until the machine has cooled down.

The door will not open at
the end of a wash
programme.

Press against the door handle, switch the machine
off and then back on again. Then pull on the door
handle again.

There is still water in the
drum and the machine is
unable to drain.

The drainage system may be blocked. Clean the
drainage system as described in the next section.

If you still cannot open
the door:

The door handle has a safety device to prevent
damage to the lock. Press firmly against the door
handle until you clearly hear the safety device
engage.

To continue a programme after a power cut

Possible cause

Remedy

Power cut.

Confirm the message shown in the display by
pressing short cut button

D

and then press the

Start

button. The programme will then continue with

the next programme stage.

Switch the machine off
and then back on again
with the

On/Off button.

Problem solving guide

42

«
...
40
41
42
43
44
...
»

Содержание PW 5105 Vario





























































Отзывы:

Нет отзывов

Похожие инструкции для PW 5105 Vario

Бренд: Kärcher Страницы: 36

Бренд: Makita Страницы: 113

Бренд: Landa Страницы: 26

Бренд: Midea Страницы: 10

Бренд: Maytag Страницы: 48

K 4 Universal Edition

Бренд: Kärcher Страницы: 32

Бренд: Gibson Страницы: 14

Бренд: GE Страницы: 70

CLOTHES-PROCESSOR EZ 3600 CEE

Бренд: Equator Страницы: 16

Бренд: Daewoo Страницы: 10

Бренд: CORBERO Страницы: 20

Бренд: Jackson MSC Страницы: 64

Бренд: IKEA Страницы: 16

Бренд: Maytag Страницы: 24

Бренд: Electrolux Страницы: 27

Бренд: Electrolux Страницы: 28

Бренд: Electrolux Страницы: 22

Бренд: Kogan Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды