Miele PW 5105 Vario Скачать руководство пользователя страница 39

Страница: 39 / 60

A fault message appears in the display

Message

Possible cause

Remedy

Water intake fault
Open the stopcock
and
check the inlet hose.

The water inlet is
blocked or restricted.

Check whether

– the stopcock is opened

enough.

– the inlet hose is kinked.

The water pressure is
too low.

– Select

Low water

pressure

in the

Settings/Supervisor level

menu.

Technical fault

There is a fault.

Start the programme again.
If the fault message appears
again, contact the Service
Department.

Fault
Disinfection
temperature
not reached

During the disinfection
programme the water
temperature was not
reached.

The machine has

not

carried out the disinfection
cycle correctly.
Start the programme again.

Drain fault
Clean the drainage
system.

The water outlet is
blocked or restricted.

LP version: Clean the
drainage system.

AV version: Call Service.

Fill the container

One of the external
detergent containers is
empty.

See "Detergent - Empty
sensor".

Fault
Container empty

To switch off the fault message, press the multi function selector.

Problem solving guide

Содержание PW 5105 Vario





























































Результаты поиска

Содержание PW 5105 Vario

Отзывы:

Похожие инструкции для PW 5105 Vario

Бренды по названию

Популярные бренды

Miele PW 5105 Vario, Инструкции по эксплуатации и монтажу

Результаты поиска

Содержание PW 5105 Vario

Отзывы:

Похожие инструкции для PW 5105 Vario

Бренды по названию

Популярные бренды