Miele G 676 Скачать руководство пользователя | Manualshive

Страница: 9 / 84

background image

Caring for the environment

Disposal of the packing material

The transport and protective packing
has been selected from materials
which are environmentally friendly for
disposal and can normally be recycled.

Rather than just throwing these ma-
terials away, please ensure they are of-
fered for recycling.

Disposal of your old machine

Old machines contain materials which
can be re-cycled. Please contact your
local authority or scrap merchant about
potential recycling schemes, before dis-
posing of the appliance.

Ensure that the machine presents no
danger to children while being stored
for disposal. See the appropriate sec-
tion in the Warning and Safety instruc-
tions.

Energy saving washing

These dishwashers are exceptionally ef-
ficient in their use of water and elec-
tricity. You can make the most of your
appliance by following these tips:

If your household water system is
suitable, this dishwasher can be con-
nected to a hot water supply, for fur-
ther economies.
However, if your water is heated by
electricity we would still recommend
connection to cold water.
In the UNIVERSAL 55° programme,
depending on the capacity of the
dishwasher, when connected to hot
water at 55°C up to 0.7 kWh of elec-
trical energy is saved. The hot water
provides this energy, and the ap-
prox. 0.13 l oil or 0.14 m

3

natural gas

needed to heat the water might be
considerably more cost effective.
Although all stages of the wash then
take place with hot water, savings
are made in cost, time and energy.

Make full use of the baskets without
overloading the dishwasher for most
economical washing.

For small loads:
Select the additional “Top Solo” op-
tion (see section “Additional options”)

Choose the programme to suit the
type of crockery being washed and
the degree of soiling.

If baskets are only half full use the
ECONOMY programme.

Use the correct dosages of deter-
gent.

Caring for the environment

9

«
...
7
8
9
10
11
...
»

Содержание G 676





















































































Отзывы:

Нет отзывов

Похожие инструкции для G 676

Бренд: Washtech Страницы: 44

Бренд: Haier Страницы: 14

Бренд: Haier Страницы: 2

Бренд: Heinner Страницы: 86

Бренд: Samsung Страницы: 40

WF16J9000K Series

Бренд: Samsung Страницы: 52

Бренд: Samsung Страницы: 44

WF16J9800K Series

Бренд: Samsung Страницы: 54

Бренд: Samsung Страницы: 44

Бренд: Samsung Страницы: 48

Бренд: Samsung Страницы: 44

Бренд: Samsung Страницы: 132

Бренд: Samsung Страницы: 40

Бренд: Fisher & Paykel Страницы: 19

Бренд: Maidaid Halcyon Страницы: 17

Бренд: Lett Страницы: 52

Бренд: Jenn-Air Страницы: 14

WAREFORCE UH 30

Бренд: Jackson Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды