Miele G 676 Скачать руководство пользователя

Страница: 59 / 84

Installing a freestanding dishwasher

Bow the panel slightly, draw out from
under the control facia and remove.

Shorten the decor frame strips, and
the packing card (if used) by meas-
urement "

When using the decor panel sup-
plied: Draw a line to join the two
marks for measurement "

". Shorten

the decor panel along this line.

Note:
When the decor frame strips are short-
ened, the hook at the lower edge is cut
off. It is however only needed for full
length decor frame strips to give addi-
tional fixing to the door outer panel.

Loosen the screws

in the door

outer panel, but do not screw out
completely.

Push the lower edge of the adapter
plate

(corresponding to measure-

ment "

") upwards far enough for its

lower edge to be in a line with the
lower edge of the adjacent kitchen
unit door front(s).

Tighten the screws

in the adapter

plate.

Installing a freestanding dishwasher

Содержание G 676





















































































Результаты поиска

Содержание G 676

Отзывы:

Похожие инструкции для G 676

Бренды по названию

Популярные бренды

Miele G 676, Руководство по эксплуатации

Результаты поиска

Содержание G 676

Отзывы:

Похожие инструкции для G 676

Бренды по названию

Популярные бренды