Miele G 676 Скачать руководство пользователя | Manualshive

Страница: 30 / 84

background image

Programme chart

Programme

When to use

Detergent

containing

chlorine

1)

chlorine-

free

2)

Compart-

ment I

(Pre-wash)

Compart-

ment II

(Wash

cycle)

Compart-

ment II

(Wash

cycle)

Normal- and Universal-Programmes

NORMAL 55 °

for

normal

everyday loads,

particularly suitable for chlorine-free detergents

100 %

100 %

UNIVERSAL 55 ° for

normal

everyday loads

20 %

80 %

100 %

UNIVERSAL
PLUS 55 °

3)

as UNIVERSAL 55 °,
but with longer wash time for

heavily soiled

loads,

particularly suitable for chlorine-free detergents

20 %

80 %

100 %

UNIVERSAL 65 ° as UNIVERSAL 55 °,

but with higher wash temperature for

stubborn

dried-on

particles

20 %

80 %

100 %

Special-Programmes

ECONOMY 55 °

for

full

loads with

very light soiling

, e. g.

coffee cups
or:
for

half

a normal everyday load, for cleaning

normally soiled

every day loads,

50 %

50 %

GENTLE 45 °

,,Gentle programme“ for

lightly soiled

crockery

and for

heat sensitive

crockery

50 %

50 %

PRE- WASH

for rinsing crockery to avoid smells if a
complete cycle is not needed

The amount dispensed will depend on the type of detergent being used:
1) Use this method for:

– detergents containing phosphates and chlorine (except liquid detergent)
Divide the total amount proportionally between compartment I and compartment II.

2) Use this method for:

– detergent which is chlorine and phosphate free
– detergent which is chlorine free but contains phosphates
– liquid detergent
In this instance the whole amount is placed in compartment II

For the NORMAL programme and the UNIVERSAL programmes use at least 30 ml (or g) detergent un-
less advised to use more by the manufacturer, then use what they advise.

If the “Top Solo” option is selected the appropriate amount of detergent according to the degree of soil
should be added to compartment II only (approx 2/3 of the total amount required for full load).

Programme chart

30

«
...
28
29
30
31
32
...
»

Содержание G 676





















































































Отзывы:

Нет отзывов

Похожие инструкции для G 676

Бренд: GE Страницы: 26

Бренд: Unimac Страницы: 2

Бренд: B&C Technologies Страницы: 38

Бренд: Fagor Страницы: 78

Бренд: Fagor Страницы: 20

Бренд: Fagor Страницы: 2

Бренд: Fagor Страницы: 1

Monogram ZBD0700

Бренд: GE Страницы: 32

Бренд: Candy Страницы: 136

Бренд: Candy Страницы: 41

Бренд: Samsung Страницы: 96

Бренд: Maytag Страницы: 56

Бренд: Fagor Страницы: 115

Бренд: Atag Страницы: 44

Бренд: Hotpoint Страницы: 10

Бренд: Classeq Страницы: 21

Бренд: Samsung Страницы: 48

Бренд: inventum Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды