Miele Allerdry T 4464 C Скачать руководство пользователя | Manualshive

Страница: 41 / 56

background image

Room in which the dryer is located

Air taken in for use in the drying
process will be warm when it is
expelled from the rear of the dryer. This
expelled air heats up the air in the
room. It is therefore very important to
ensure that the room is adequately
ventilated, particularly if the dryer is
located in a small room. Otherwise
running times and energy consumption
could be increased.

Washer-dryer stack

The tumble dryer can also be
combined with a Miele washing
machine in a washer-dryer stack. To do
this the appropriate stacking kit* (WTV)
to match your washing machine is
required.

* Available as an optional accessory
from your Miele dealer or the Miele
Spare Parts Department.

,

Stacking kits must only be

installed by a suitably qualified fitter.

Before moving the machine again
(e.g. when moving house)

After each use a small quantity of
condensed water will collect in the area
around the pump. This water can run
out, if the machine is tipped up when it
is being moved. It is a good idea to run
the

Cool air

programme for

approximately 1 minute before moving
the machine. Any remaining condensed
water will then be fed into the
condensed water container or out
through the drain hose.

Installation and connection

41

«
...
39
40
41
42
43
...
»

Содержание Allerdry T 4464 C

























































Отзывы:

Нет отзывов

Похожие инструкции для Allerdry T 4464 C

Бренд: NEFF Страницы: 48

Бренд: Lotus Страницы: 22

Бренд: GE Страницы: 60

Бренд: MagiCater Страницы: 40

Бренд: Gaggenau Страницы: 10

Immortal Power-life

Бренд: Amika Страницы: 23

Satin Hair 5 HD585

Бренд: Braun Страницы: 8

Бренд: Noble & Price Страницы: 4

Бренд: Crosley Страницы: 32

Бренд: Summit Страницы: 15

Бренд: Haier Страницы: 16

HDY-C70 WH HA AA

Бренд: Haier Страницы: 17

Бренд: Haier Страницы: 24

Бренд: Haier Страницы: 17

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 32

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды