manualshive.com logo in svg

Miele Allerdry T 4464 C, Руководство по эксплуатации

Поделиться
Скачать
Miele Allerdry T 4464 C Скачать руководство пользователя страница 50

Anti-crease

If laundry is not removed as soon as
the programme has finished, the
drum will continue to rotate at
intervals for one hour to prevent
creasing.

The anti-crease function

– is activated when the machine is

delivered. You can deactivate it if
wished.

– is present on all programmes except

Woollens hand care

.

– should be left activated, if laundry is

not normally removed immediately
after the end of a programme.

Follow steps

A

to

F

to programme and

store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

– The programme selector is at

Finish

.

A

Press the

Start

button and keep it

pressed in whilst carrying out steps

B

-

C

.

B

Press the

I-On/0-Off

button in.

As soon as the indicator light for the

Start

button lights up constantly . . .

C

. . . release the

Start

button.

D

Turn the programme selector to the

Cottons Machine iron

position.

P

...

i

will appear alternately in the

display to show that a setting is
selected.

The number which appears alternately
in the display with

P

means:

I

Anti-crease activated

(the

Drying

indicator light will also

flash)

0

Anti-crease deactivated

E

Pressing the

Start

button switches

from one number to the other.

F

Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now
stored in memory. You can change it
again at any time.

Programmable functions

50

Содержание Allerdry T 4464 C

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды