Midland 70-066 Скачать руководство пользователя страница 49

Страница: 49 / 74

Midland 70-066 low Band Conversion to 6 Meters: Synthesizer Part 2 Page 2.

Receiver Local Oscillator Alignment:

The main Receiver VCO is set to a frequency which is center of the programmed frequencies, By using the

m6m-5k.bin

EPROM [Generated from VK2DOT RT85 Software or other software] – set to

channel 48

[53.225Mhz].

Connect the frequency counter to

J365.

The frequency counter should read

74.625Mhz

Connect DC Voltmeter between ground and

TP701

. On 10 Volt Range.

With the correct alignment tool on all ferrite cores adjust the ferrite cores – the ferrite slugs are easily
broken.

Adjust L702

such that the DC voltage at

TP701

is centered on 3.5V for all programmed channels

(i.e. some above 3.5V and some below 3.5V). Voltages will swing between 2 Volts and 4 Volts.

NOTE:

f= (RX freq - 21.4MHz) +- 244Hz : for V HF(HB) and UHF

f= (RX freq + 21.4MHz) +- 244Hz : for VHF{LB}

52.525Mhz

= Tx frequency then

73.925Mhz

= Rx Oscillator frequency.

Transmitter VCO Alignment:

Ensure that the exciter output is disconnected at J366.

Connect the frequency counter to

J366.

The transmitter output local oscillator frequency will be at

the transmitter frequency. Ie for channel

will be

53.225Mhz

when transmitting.

******

A: The main transmitter VCO should be adjusted on the

highest

transmitter programmed frequency.

Adjust channel to channel

[

53.975Mhz

With DC Voltmeter still connected between ground and

TP701

and on 10 Volt Range; Key the

transmitter and adjust L702 to give 4.0 Volts at TP701.

B: Connect DC Voltmeter between ground and

TP101

. On 10 Volt Range.

With the correct alignment tool on all ferrite cores adjust the ferrite cores – the ferrite slugs are
easily broken.

Operate the PTT button. Check the voltage at

TP101

and re-adjust L107 for a voltages

around 4.5V for the TX channel. Release the PTT button.

Transmitter Driver Alignment:

Connect a DC voltmeter to pin 2 of

CM101.

Set channel to center frequency. Ie.

channel 48

[53.225Mhz].

Adjust CV102 for a dip between two peaks.

Содержание 70-066











































































Результаты поиска

Содержание 70-066

Отзывы:

Похожие инструкции для 70-066

Бренды по названию

Популярные бренды

Midland 70-066, Руководство пользователя

Результаты поиска

Содержание 70-066

Отзывы:

Похожие инструкции для 70-066

Бренды по названию

Популярные бренды