Midland 70-066 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 74

background image

Rx Tune Up.

Midland 70-066 Receiver Alignment Points Above:

Receiver tune up is straight forward. Reconnect the Receiver Local Oscillator J365 cable to the
synthesizer board.

LO Amplifier Alignment:

Connect multi-meter or DVM to Monitor CM202 pin 1. Note pin 2 is missing key pin). Switch to
center frequency –

Channel 49 -

53.250Mhz

[center between 53.975Mhz and 52.500Mhz.]

To tune the local oscillator multipliers - Adjust

L209 and L210

for maximum reading. A typical

reading is 0.4 V. A common problem with these transceivers is lack of LO injection if they are not
modified and tuned correctly.

RF-IF Alignment:

Tuning the RF front end - On a mid frequency channel (

Channel 49 -

53.250Mhz

) feed a signal in

from a signal generator to the Midland 70-066 antenna socket. Connect a multi-meter or DVM to
Monitor CM202 pin 2 and peak

L201, L202, L204 and L205

for maximum reading while remaining

in the linear range [ie Set signal generator level for positive meter reading before limiting occurs.. Note
the reading at this pin will be negative until sufficient RF input signal is available. Repeat adjustments
for optimum.

An alternative method is to use a Sinad meter or tune for maximum quieting. When correctly aligned
the sensitivity is typically 0.35uV for 12db sinad over the range 52.5 to 54 MHz.

Tests have concluded that the Midland 70-066 should lift the mute at 0.1uV for a reasonable audio
quality.

Quadrature Coil Alignment:

Adjust

L252

for maximum audio output.

Tight Squelch Alignment:

Adjust

RV251

for the desired tight squelch sensitivity.

Midland 70-066 low Band Conversion to 6 Meters: Receiver Ver 2.1 20-nov-09 Part 3 Page 3.9

«
...
57
58
59
60
61
...
»

Содержание 70-066











































































Отзывы:

Нет отзывов

Похожие инструкции для 70-066

Бренд: Yamaha Страницы: 8

Бренд: Yaesu Страницы: 5

Бренд: Aventura Страницы: 6

PluraSens E2638-NH3-P

Бренд: Evikon Страницы: 21

Бренд: AAS Страницы: 8

Бренд: M-system Страницы: 2

Бренд: Omicron Страницы: 25

Бренд: ATN Страницы: 35

6.1 Channel AV Reciever LR-6500

Бренд: Luxman Страницы: 36

TELEVISION RECEIVER

Бренд: Zenith Страницы: 8

Бренд: Woxcon Страницы: 7

Бренд: Aluprof Страницы: 4

Бренд: American Fibertek Страницы: 4

Бренд: e+p Страницы: 12

Бренд: Belkin Страницы: 40

FatMax FMHT1-77360

Бренд: Stanley Страницы: 154

Air-Eagle SR 38-2000-DC

Бренд: BWI Eagle Страницы: 8

ES200-7CD - REV B

Бренд: Simrad Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды