background image

 

SPECIFICATIONS

 

 
Operating Voltage 

5 VDC 

Operating Current 

8 mA 

Operating Temperature 

-30 - +60 C 

Frequency Response 

300-2400 Hz 

Input Impedance 

>25 k

Ω

 

Carrier Suppression 

65 dB < Peak Voice 

Audio Output Impedance 

<1K 

Ω

 

 

Security Specifications: TVS-2 

Encryption Sequences 

+40 Trillion 

Random Number Generator 

64 bits 

Sequence Length (est.) 

84 billion years 

 

Security Specifications: VPU-15 

Inversion Frequencies 

37 

 
 

INSTALLATION OVERVIEW

 

 
1.  Test the radio for functionality. 
 
2.  Program the radio per the Radio Programming Section of this manual. 
 
3.  Install the scrambler into the radio per the Hardware Installation Section of this manual. 
 
4.  Program the scrambler per the Product Programming Section of this manual. 
 
*** Midian is not responsible for any damage/loss resulting from the use of Midian’s products. 
 
 

GENERAL INFORMATION 

 

TVS-2:

 The TVS-2 is a high-level rolling code scrambler that uses hopping type rolling code encryption for higher 

security rather than the sweeping code type.  The scrambler is capable of features such as ANI, ENI, Deadbeat 
Disable, Spy, and more when using Midian’s Kryptic Signaling format with the CAD-300/DDU-300/TRC-300. For 
more details, please see the TVS-2 Technical Reference Manual. 
 
 

VPU-15:

 The VPU-15 is an entry level voice inversion scrambler.  The scrambler is capable of features such as 

ANI, ENI, Deadbeat Disable, Spy, and more when using Midian’s Kryptic Signaling format with the CAD-
300/DDU-300/TRC-300. For more details, please see the VPU-15 Technical Reference Manual. 
 

 

2

Содержание TVS-2-TAIT















Отзывы: