background image

  Page 14  

Ins

tallation

Ins

tructions

Window Requiri

m

ents

Do the following before beginning installation. 
See illustrations below. Check dimensions of 
your unit to determine model type:

Model type:  

15k/18k 

25k

Unit Height:  

17-5/8” 

18-5/8”

Unit Width: 

23-5/8” 

26-1/2”

Min. Window Opening: 

18-1/2” 

19-1/2”

Min. Window Width: 

26-1/2” 

31”

Max. Window Width: 

40-1/2” 

42”

Preli

m

inary Instructions

Window Sash Seal

Top Rail

Foam Gasket

3/4” Long Flat Head Bolt

Sill Angle Bracket

1 /2” Long
Screw and
Locknuts

Window 
Support
Bracket

Frame
Assembly
(Right)

Side
Retainer

Washer Head
Locking
Screw

Bottom Rail
Seal to Unit

Frame
Assembly
(Left)

Safety Lock and 
3/4” (or 1/2” ) Long 
Hex Head Screw

Locknuts

Read these instructions co

m

pletely 

and carefully.

• IMPORTANT

 - Save these 

instructions for local inspector’s use.

• IMPORTANT

 - Observe all 

governing codes and ordinances.

•  Note to Installer - Be sure to 

leave these instructions with the 
consu

m

er.

•  Note to Consu

m

er - Keep these 

instructions for future reference.

•  Skill level - Installation of 

this appliance requires basic 

m

echanical skills.

• Co

m

pletion ti

m

e - Approxi

m

ately 

1 hour.

We reco

mm

end that two people 

install this product.

Proper installation is the 
responsibility of the installer.

Product failure due to i

m

proper 

installation is not covered under the 
Warranty.

You MUST use all supplied parts and 
use proper installation procedures as 
described in these instructions when 
installing this air conditioner.

Do not, under any circu

m

stances, cut 

or re

m

ove the third (ground) prong 

fro

m

 the power cord.

Do not change the plug on the power 
cord of the air conditioner.

Alu

m

inu

m

 house wiring 

m

ay present 

special proble

m

s - consult a qualified 

electrician.

When handling unit, be careful to 
avoid cuts fro

m

 sharp 

m

etal edges 

and alu

m

inu

m

 fins on front and 

rear coils.

WARNING - Before You Begin

Save carton and these Installation 
Instructions for future reference. The carton 
is the best way to store unit during winter, 
or when not in use.

NOTE

2

Installation Instructions

Содержание MAW15R1YWT































Отзывы: