Microtek TMA 1600 страница 1 Скачать руководство пользователя

Страница: 1 / 20

Contents

Introduction ................................................................................................................ 2

Unpacking the TMA1600 ............................................................................................ 2

Unlocking the TMA1600 ............................................................................................. 3

Shipping the TMA1600 ....................................................................................... 3

Installing the TMA1600 .............................................................................................. 4

Positioning Your Originals .......................................................................................... 6

Positioning transparent originals ....................................................................... 6

A. Using the 35mm Slide Template ............................................................ 8

B. Using the 35mm Filmstrip Template ...................................................... 9

C. Using the 6 x 9 cm Filmstrip Template ................................................. 10

D. Using the 4" x 5" Film Template ........................................................... 11

Positioning X-ray originals ............................................................................... 12

Positioning reflective originals ........................................................................ 13

Your First Scan ......................................................................................................... 15

Performing Color Calibration .................................................................................. 17

The color calibration target .............................................................................. 17

Before you calibrate ......................................................................................... 17

Calibrating your target ..................................................................................... 18

Loading a profile ............................................................................................... 19

Specifications ........................................................................................................... 20

Installing and Getting Started

Microtek TMA1600

Trademarks

Microtek

, ScanMaker

, and

ScanWizard

Pro are

trademarks or registered
trademarks of Microtek
International, Inc.
Macintosh

and Apple

are

registered trademarks of
Apple Computer, Inc.
Windows

is a registered

trademark of Microsoft
Corporation. All other
products or name brands are
trademarks of their
respective holders.

Important

Documents you scan may be
protected under copyright
law. The unauthorized use of
such documents could be a
violation of the rights of the
copyright holder. Microtek
bears no responsibility for
the unauthorized use of
copyrighted materials.

Содержание TMA 1600





















Результаты поиска

Содержание TMA 1600

Отзывы:

Похожие инструкции для TMA 1600

Бренды по названию

Популярные бренды

Microtek TMA 1600, Инструкция по установке

Результаты поиска

Содержание TMA 1600

Отзывы:

Похожие инструкции для TMA 1600

Бренды по названию

Популярные бренды