background image

v

8.

Use the monitor only with the supplied adapter. In case of loss, contact the
retailer or service center.

9.

If you lose the power cord, you must purchase a power cord of the same
type and configuration.

Japan GVCTF type, 3 wires or with ground-wire; T-mark approval is
required.

U.S. GVW-1; 18AWG X 3C; SVT with national approval as UL and/or CSA
approval/number(s)

Europe GVDE/ÖVE and/or KEMA approval; H05VV-F, 3G, 0.75mm

2

, or

equivalent.

The power cord should bear the name of the manufacturer and state the
type of cord that it is.

Important Safety Instructions

Please read the following instructions carefully.  This manual should be retained for
future use.

1.

To clean the LCD monitor screen, make sure the monitor is in the power off
mode.  Unplug the monitor from its power source before cleaning it.  Do not
spray liquid cleaners directly onto the unit.  Stand away from the LCD
monitor and spray cleaning solution onto a rag.  Without applying excessive
pressure, clean the screen with the slightly dampened rag.

2.

Do not place your LCD monitor near a window.  Exposing the monitor to
rain, water, moisture or sunlight can severely damage it.

3.

Do not place anything on top of the monitor-to-PC signal cord.  Make sure
the cord is placed in an area where it will not be stepped on.

4.

Do not apply pressure to the LCD screen.  Excessive pressure may cause
permanent damage to the display.

5.

Do not remove the cover or attempt to service this unit by yourself,as you
may void the warranty.  Servicing of any nature should be performed only
by an authorized technician.

6.

Safe storage of the LCD monitor is in the range of  -4°F to 140°F (–20°C to
+60°C).  Storing your LCD monitor outside this range could result in
permanent damage.

7.

If any of the following occurs, immediately unplug your monitor and call an
authorized technician.

The power or monitor-to-PC signal cord is frayed or damaged.

Liquid has been spilled onto the monitor, or it has been exposed to rain.

The monitor has been dropped or the case has been damaged.

Содержание 710S






















Отзывы: