background image

V. TECHNICAL DATA

Analog input                                                                                                     from bridge weight sensor  

- power supply  / sensitivity of the 
sensor

   5 V D / 1 ÷  7 mV/ V  

  ...................................(other)  

- measurement accuracy

0.003%

- temperature stability

5 ppm/ °C

- conversion time without software 
filter:
- fast / slow conversion 

According to the configuration of order code
and from  SYST/rS485/bit6 menu:

 - 12.5 / 100 mS или  60 / 100 mS  

- software filters:

      arithmetic mean - of 1

   level exponential  – of 2 level  

Arithmetic mean - 1 ÷ 16 measurements     ( х10 ms)

exponential         - attenuation % - 0, 50, 75, 88, 94 %

  Analogue output, DC                                                                                                                                  1 

- transmitting the measurement

 

0 ÷ 20 mA   

4÷ 20 mA    

0 ÷ 10 V .......................

other 

- conversion accuracy 

0.003%

- temperature stability

5 ppm/ °C

- output forming time

60ms

- measurement part insulation

1500 V DC for 1 s

  Digital inputs                                                                                                                                               4  

  Tarе, Zero/Start,
  S1, S2-selection set of parameters-2

Low active level NPN to GND iso

minimum time to Tare and Zero tmin= 20 ms

  Digital outputs                                                                                                                                           3

K1, K2, K3

Реле 250 VAC / 3 A - 

SPST

 - NO

NPN OC iso 70 mA 70V transistor open collector, 
unsulated from measurement part, required an external 
power supply. Unsulation - Viso = 3750 V 

output forming time

20 ms

  Communication

MODBUS RTU RS485;  

9600 bps; parity non/even; 1 / 2 stop  

Power supply

Power supply

 

80 ÷ 250 VAC ; 50 ÷ 60 Hz 

 

24 V DC 

 Display and Keypad

- display range

6 seven segment LED's 14 /или10/ mm            - 99999÷99999

- display format

XXXXX, X

.

XXXX, XX

.

XXX,  XXX

.

XX XXXX

.

program selectable, by decimal point  

- display color

red,  

green, transparent 

- LEDs

4  

- keypad  

Semi sensor keypad

Ambient conditions

  Operating temperature / humidity

    0 ÷  50 °C / 0 ÷  80 % rh  

  Storage temperature / humidity

 -10 ÷ 70 °C - 0 ÷  95 % rh  

Protection class

IP 65

Dimensions

Overall dimensions (WxHxL)

121 х 171 х 58 mm

Mounting

On wall

Weight

Max 540 g

  Software version: 

v1.1

For discrete outputs open collector logic 0 depends on the load on the output:

Vce ( sat )

  ≤ 1.00 V at Ic = 70 mA.  

Vce ( sat )

  ≤ 0.75 V at Ic ≤ 10 mA

Document revision  2015-08-17

4

Содержание MS8357

















Отзывы: